Notifications
Clear all
Search result for: evans coolant
| # | Post Title | Result Info | Date | User | Forum |
| 2015 Ford Fusion coolant issue.....or not? | 17Relevance | 5 years ago | fedup1982 | Submit Your Question HERE | |
| I have a 2015 fusion 1.5 ecoboost. I replaced the motor 300 Miles ago with a new block and head along with other new parts. Shortly after I noticed coolant loss, and realised the charge air cooler in the intake was cracked and leaking coolant. Fixed that! Then it appeared the coolant level was dropping and rising (Im aware of expansion of the coolant) I bought a head gasket co2 leak test test and it doesnt show any signs of a leak, I havent noticed any exhaust since what I assume was the residual from the intake burnt off. Should I worry or just keep an eye on the coolant? Could it be air in the cooling system? Expecting the worse but hoping for the best. Worse case in another 100 miles I will be checking valve clearance so I could "easily" replace the head gsaket at that point. | |||||
| 2002 Honda Civic overflow tank filling with coolant | 17Relevance | 5 years ago | Nathan Brawley | Submit Your Question HERE | |
| Hey I have a 2002 Honda Civic with a manual transmission. I have had an issue with my coolant overflow tank filling up with coolant and sometimes spitting coolant out of it when it is full. I have replaced the radiator and cap and thought that is was good but now it is still happening again. I have also tested for a blown head gasket with that color changing liquid and it says that it’s not blown. I am unsure of why it is still doing this still. Is it possible that there is air in the system and that’s possibly why it’s pushing coolant into the overflow? Also is it normal for the coolant in the overflow to fluctuate or just stay at the same level all the time? Thanks | |||||
| Answer to: Transmission fluid and coolant/antifreeze replacement? | 17Relevance | 6 years ago | geriscan | Submit Your Question HERE | |
| There are two factors in determining fluid changes: Miles and time. The miles are not a problem, here. The time is a problem. Both fluids have additives that lubricate and prevent damage. Given what you're communicating (no fluid changes in thirteen years), there's bound to be trouble. I would not be surprised if the transmission seals are hard as rock. And if you want to assess the corrosion level of the coolant, just use a multi-meter and measure the electrolysis. Anything over .3 (red probe in the coolant with the cap off and black grounded on the car) shows that electrolysis is corroding your vehicle. Likewise, you can use a fish tank pH level strip to determine the level of acidity in your coolant. Anything below 7.5, well, it's time to change the coolant. Below 7, the coolant is acidic and is actively corrode aluminum. The result of the process is aluminum oxide, which is a form of sandpaper circulating between your radiator and your engine. | |||||
| 97 Nissan Quest coolant leak: water pump vs bypass hose vs plug on the front of the rear cylinder head? | 17Relevance | 6 years ago | czi50agjb8wa | Submit Your Question HERE | |
| Researching a 204k mile 97 Nissan Quest that's been left sitting for 3 years because of a cooling leak that seems to be dripping above the oil filter. It's currently a crank no start, but I would like to make sure the cooling system is sealed before tackling that issue. The coolant reservoir tank was empty so I added half a gallon of distilled water before using a pressure tester. It initially dripped below the oil filter, but I think it finally bridged below the crank pulley because I jacked the front to get a better view. It's still too tight & dark a space to definitively find the location of the leak so I uploaded a clip ( Around the 16 sec mark, I have noticed a wiring harness that's looks moist so I'm not sure I'd that could've been from the c shaped hose above, but there was a drip around the 36 sec mark. I didn't feel any wetness from the coolant hoses though. According to the owner, the water pump along with the timing belt was replaced around 140-170k. He has driven it for months after, but then didn't drive it as much. He stopped driving it when he noticed the leak so it's been sitting for years. I think it might be this ( : "Coolant Leak From Plug Behind Timing Cover on Nissan Quest Problem Description A coolant leak may develop from a plug on the front of the rear cylinder head, behind the timing cover." I haven't seen YouTube videos about fixing just that plug or if that part is even available. I don't even know what it looks like. Any one have videos or pictures if it? I've read about coolant leaking from the timing cover, but some have reported that even after replacing the water pump, it still leaked. I know that there is a possibility that the new water pump replacement croaked, but what are the odds? Looking up YouTube videos, the first one that pops up is a faulty bypass hose (uploader initially replaced water pump as well), but that was for a Q. Hopefully the clip will give better data for someone who has experienced this issue. Thanks. | |||||
| How to fix Toyota Hilux losing coolant | 17Relevance | 6 years ago | bushman24 | Submit Your Question HERE | |
| Make - Toyota Model - Hilux Year - 2016 Mileage -28000 Miles Tranmission- Automatic I’m experiencing some weird behavior with my coolant. My vehicle contains an expansion tank system and a radiator without a cap. i noticed the coolant was below the Low level and topped it up using Toyota Original Long Life coolant as recommended by my owners manual. After driving for a day the coolant dropped back to the same level and remains stable at that level when cold ever since. I assume if there was a leak or blown head gasket I would continuously be loosing coolant, but it just remains stable at that level below low. I have topped of three times after and confirmed the same behavior. any ideas ? | |||||
| Answer to: Coolant Smell after Head Gasket Replacement and Longer start time after valve adjustment | 17Relevance | 6 years ago | jack62 | Submit Your Question HERE | |
| So in your shoes, after spending big bucks for a head gasket job and then smelling coolant in the exhaust and hard starting, my concern would be if the head gasket is still leaking coolant into a combustion chamber(s). (Cylinder(s)) I'd want an answer to this first, so get yourself one of those Combustion Gas test Kits. If coolant is leaking into any of the combustion chambers and being "burned" where you can smell it in the exhaust, then combustion gasses will also be leaking back into the coolant system. As far as the valve adjustment, if the mechanic adjusted them too loose you'd hear them clattering. Too tight and the valves wouldn't close completely and you'd be experiencing reduced compression and driveability issues. Valve adjustments aren't hard and any competent mechanic won't screw them up. Watch Scotty's video on combustion gases in the coolant system/testing for leaky head gaskets with a Combustion Gas test Kit. (Costs about $30 bucks) | |||||
| Answer to: Coolant Smell after Head Gasket Replacement and Longer start time after valve adjustment | 17Relevance | 6 years ago | Dion | Submit Your Question HERE | |
| My take on this is thst you smell the coolant as before the head work was done coolant had seeped into the exhaust and into the muffler. Now that the work is done..the coolant still remains and is getting burned off little by little. Another scenario is that coolant is still leaking into the engine but you would only know that if the coolant reservoir is getting emptied little by little. As for hard starting..You would have to revisit the valve adjustment as it may be still too tight and need to be loosened in my opinion in order for easier starting. It comes down to you going back to the shop and explaining your concerns and seeing if they have a good answer and or a fix to make it normal to start and not to smell. | |||||
| Loosing Coolant, but so far have checked everything I can think of? | 17Relevance | 6 years ago | ShadowOfNoc | Submit Your Question HERE | |
| 2011 v6 Ford Mustang Automatic w/ 46k miles I am losing coolant (the res level is very slowly going down when I check it over the period of a month) but: - Not a drop under the car/no puddle - Nothing under the dash/on the floor of the passenger side (no heater core leaking) - Cannot smell any coolant from inside/outside the cabin when car is running or turned off - Cooling system pressure test is fine and holds exact same pressure for 45+ minutes - No white smoke out of the exhaust (besides the normal bit of steam in very cold weather or the little bit that goes away after the car warms up when you start to drive after a cold start) - No oil in coolant - No coolant in oil (no milky/wet/foamy oil) - No coolant/water under bottom of oil cap - Replaced res cap (radiator doesn't have a cap, the pressure is held at the res) with brand new Ford OEM cap Any ideas? A pressure test would find a bad head gasket, right? | |||||
| Idle Problems, Poor Fuel Economy & Rust in the coolant - 2001 Honda Accord | 17Relevance | 6 years ago | quinoa_baby | Submit Your Question HERE | |
| Hi everyone, A couple months back I bought a used 2001 Honda Accord LX (4-cyl engine) with 150k miles on it. Recently, Ive been experiencing some idle issues with the car and I've also noticed that the fuel economy is pretty garbage. When I try to accelerate, the RPM will remain stagnant for a lil bit and after a few seconds it starts to climb normally. Then, when I'm above 2500 RPM and I try to reduce speed or stop the car the RPM will plummet and sometimes surge, fluctuating between 1000-1500RPM for just an instant. The CEL codes that have popped up are a P0172 code (system running rich) and a P0420 (catalytic converter below efficiency threshold). Could the system be running rich due to a problem with the fuel system (i.e., clogged fuel filter, clogged fuel injectors or some other fuel system failure) or could it be running rich from a vacuum leak? It should be noted however that after a few days the check engine light turned off without me having to connect the scan tool. I also recently noticed that the car is running with rust in the coolant when I went to check the coolant level. When inspecting the coolant lines I noticed that there was one going to a part in the throttle body (just below the intake inlet) that seemed off color. When I removed the line I saw that the tube connecting to it was badly eaten up by rust. I don't know if this is the sole culprit of the rust in the coolant but its definitely a place to start. I dont know exactly for how long this has been going, but it seems like it could be potentially dangerous if left unchecked. The coolant is no more than 3 months old and Ive barely put 3000miles on the car since I bought it. Can anyone here offer some sort of advice on how to diagnose the idle and poor fuel economy problems? And how should the rust issue be approached? I imagine a flush is in order, but what would be the best way to do it and what should I be aware of? | |||||
| Answer to: Coolant Level on '94 Toyota Camry | 17Relevance | 6 years ago | Razmig Bartassian | Submit Your Question HERE | |
| Hello there! Congrats on your first car! Your coolant level being on MAX when the engine is hot is totally normal. coolant expands when it is hot, which is why there is a huge gap between the MIN and MAX level. coolant reservoirs are also known as expansion tanks because of this. If it is on MAX when the engine is cold, then you're at risk of potentially overflowing the tank. You'll just need to siphon some out of the tank until it's at the MIN line. If your coolant temperature gauge is going past halfway, then it's time to do a coolant flush and perhaps replace the radiator. Hope this helped you! NOTE: Never attempt to open the expansion tank when the engine is hot! It is a pressurized system. Only do this when the engine is cold. | |||||
| Is there Oil in my cooling system? | 16Relevance | 2 years ago | JesseDavis | Submit Your Question HERE | |
| Hi all, Novice DIYer here. Preforming my first radiator flush. Pictures below are a result of the first flush. I used a rad flush product along with some distilled water for my first round. when emptying my Radiator I noticed some streaks in the coolant in my catch can. When purging out all the air, some of the residual fluid made its way up the funnel. I noticed a little bit of streaking in it as well. I want to be cautious here, is this oil or a result of the radiator flush / old coolant still in the system? thanks for taking the time to answer my question. I appreciate the time. (1993 Mazda Miata) (211,000 Kilometers / 131,000 miles) Catch Can : Result of first flush Funnel while purging air to fill for second flush : | |||||
| 2019 GMC Acadia 3.6 liter AWD | 16Relevance | 3 years ago | lost-in-Michigan | Submit Your Question HERE | |
| Hi. I have a P01FO code on my SUV. I wonder if there should be any coolant in the recovery/surge tank when the engine is cold? If yes, how much? Currently, when cold, the tank is empty. I added some coolant to the recovery/surge tank and let the engine run for around 20 minutes; next, I drove the vehicle for about 20 minutes. When I returned, the surge tank was filled to the hot level. Hours later, I checked with a cold engine; the surge tank was empty. I do not have any signs of the coolant leaking onto the floor, and the motor oil is not milky or shows any other indication of coolant in it. Another thing is I do not have any of the characteristics that go along with the code P01F0 outside of the check engine light. The temperature gauge shows the same temperature level. The needle is on the line right before the halfway point between 'C' and 'H". No reduced power steering assist warning. The heater pumps out heat. The AC is cold, No hard starts, No change to the exhaust fumes. So, I am wondering if the cooling system is low on coolant since there is none in the recovery/surge tank when the engine is cold, and if that is the case, how much should there be? Since I live in Michigan and have an unheated garage, I would like to avoid replacing the coolant temperature sensor or the thermostat until warm weather returns. Thanks Mark | |||||
| Answer to: Should I accept a free 1993 Volvo 960 that needs a lot of work? | 16Relevance | 3 years ago | BobTheHatKing | Submit Your Question HERE | |
| TLDR it engine runs strong and it runs and drives ok but it needs quite a bit. Picked it up late August. Before I picked it up, my friend used one of their 3 AAA tows to tow it to a shop, and while they were at it AAA gave us a new battery under warranty. At the shop I had the coolant leak diagnosed and it was an upper radiator hose so that was replaced there. Also paid for an inspection, coolant top off so that they could do the head gasket test (because it had like no coolant at all) since it did have cooling issues. The shop was also a smog shop so I had a pre-test done there since my friend had lost the paperwork from the last smog test. Failed by just barely. The mechanic said he could guarantee it to pass for $450: spark plugs, fuel injection, decarbonize engine, intake & cat cleaner, and the smog retest and paperwork itself. I knew I could do all that labor myself for less, but then no guarantees so I opted to pay the extra money and it did pass. Total $745. Drove it home about 5 miles with no issues. About a week later I noticed the coolant was still leaking so I took it back and had them rediagnose (for free ofc) and they said radiator. I’ve put Bar’s stop leak concentrate, but since I’ve barely driven it since it brought it home the second time while waiting on parts, I don’t think it’s had the chance to get to full operating temp to seal it, so we’ll just have to see if it works. It’s a very gradual leak. Also turns out the spark plugs were practically brand new but I didn’t know that until my friend gave me the service records afterwards. The registration was late by almost 2 years, so I paid for 2022 and 2023 with late fees, as well as registration through oct 2024, and also lost title and the transfer fees. Total: $382+198 in credit because my friend had already paid for 2021, but due to it failing smog the car was not properly registered. The mileage on the car was 159,487 and not 163k as previously thought. When I got the car, there was a stack of paper dixie cups holding the headlamp in on one side because it kept popping out of the socket of the lens. It was pretty funny but hey, it worked, and it didn’t catch fire! But as it turns out someone simply forgot to put the thing that screws the bulb back on. I compared it to the other side and found the part inside the cabin. Both of the turn signal lenses were cracked in the front, so I popped in two new ones for stupid cheap and new LED bulbs because apparently they cracked due to the intense heat of the incandescent bulbs. Only problem is the LEDs will make the turn signals flash faster because they use less voltage so it thinks a bulb is out. If anyone knows a way of tricking it to be normal lmk.I went to fill the washer fluid reservoir and it all just came out, so I thought oh I’ll just jb weld it, but turns out it was just a rubber hose that fell off. Now it’s full of fluid but it still doesn’t squirt. Haven’t gotten around to figuring that out yet. There’s a light on indicating a fault in that system. Later, I left the dome light on for 24 hours, and it still started right up so I turned it off and left it alone. A couple of days later it would not start, and we tried a bunch of things after a jump didn’t help. As it turns out, the measly 590 CCA battery in my daily (09 Taurus) wasn’t enough to jump the 730 on this car. Put it on a trickle charger overnight and it worked. One of the things that happened though when we were trying to figure it out though, was we swapped a horn relay with another relay (ignition or fuel pump I think). When it finally started up, the horn didn’t work, so I went to swap the relays back around, which worked, but in the process I pulled the wires out of the relay housing. I thought I’d need new relay housing, so I taped them up with electrical tape so that they wouldn’t short out, but that caused some confusion because the wires were all mixed up. I wrote everything above a while ago and there was more to that story but I forgot to finish and don't remember what I was gonna say. I did end up fixing the horn and we just put the wires on the relay without the housing and it drove fine so I ignored it until today when the horn broke again. As I was fiddling around with the relays, I started it up and got a transmission fault light. I messed with the relays a few more times and started it up each time but it still didn’t fix the horn or the transmission code, but I decided to see if it would go into gear and reverse which it did. Since it did, I was ready to give up on the transmission fault and ignore it, and when I started it up one last time the light went away. Horn still broken tho. The coolant leak seems to have either been sealed or gotten smaller I can’t really tell. The original radio with cassette still works, along with the electronic retracting antenna. I did have to call the dealer for the radio code, and they told me you can try #### but the radio was replaced under warranty in 94. So I tried it and well, it worked! Thanks to those mechanics in 94 for resetting it to the same thing. Now the speakers are a different story: some of them cut in and out but smacking it or the radio sometimes fixes it. It also tends to work best at max or near max volume, which thankfully isn’t crazy loud. Some other issues it has: the leather seats in the front are cracked and torn and the paint is rough, and there’s caked on dust that I can’t get off. Haven’t gotten around to cleaning the very dirty carpets either. The power windows and power sunroof get stuck sometimes. There is a pen stuck in one of the driver’s seat tracks so the seat will sort of pivot instead of going forward and back lmao. Transmission sometimes shudders when going in and out of reverse. The cruise control actuator broke off right before I got it, but I’ve got more important things to do so I won’t be replacing that anytime soon. There’s a steering noise when I make sharp turns and a leak in the rack, so I’m going to try changing the fluid and putting in at-205 and see if that fixes it. There’s a crack on the top of the radiator fan housing but it hasn’t fallen off yet (I think it’s still bolted on at the bottom) so idc. A/C doesn’t work either (might just need refrigerant) and sometimes the heater when it decides not to blow any air. There was a slight fuel smell sometimes when I shut it off but it might have gotten better recently. Hood struts don’t work but it has a locking mechanism that keeps it from falling down. Trunk struts are also shot and that one is a death trap because it could either fall on you, or it’s old enough that there’s no emergency release inside (if anyone wants to kidnap someone… wink wink). Apparently it loses oil but I have yet to see if it really does. As I mentioned, the rear is sagging but it drives fine so just going to ignore it for now. Rotors, diff oil, and timing belt need to be done soon too, but my garage is currently occupied while I try to salvage my daily which went over train tracks. This car was not supposed to be my daily but it is now…I also lost my coolant reservoir cap once and drove without it 17 miles to school and back XD | |||||
| Car Overheating after Driving on Highway More than 60 miles | 16Relevance | 3 years ago | E_Bizzle | Submit Your Question HERE | |
| Hi Scotty, I have a 2005 Honda Civic DX with a 1.7l SOHC engine, an automatic transmission, and 183,000 miles. A few months ago the engine over heated on a long highway trip. The coolant was lower than normal. I replaced the radiator 5 years ago at 136,000 miles. I replaced the timing belt, water pump, thermostat (I tested the thermostat before installing), radiator cap, coolant, and chemically flushed the radiator last month at 182,000 miles. I tested for a head gasket leak with a combustion leak detector. The chemical never turned green after 10 minutes of testing. The engine was plenty hot and thermostat was open. There are no visible external coolant leaks. I checked the spark plugs and they all look the same. No white smoke at the tail pipe. There is no milky oil. I've cleaned the overflow reservoir hosing. I've replaced the transmission fluid. I've cleaned the grill of the radiator and condenser. The fans work as expected and cycle on and off normally. However, the car is still over heats when continuous driving on the highway for more than 80 miles. The car doesn't over heat when driving in town (20-30 minute drives less than 50 miles). I've noticed the overflow reservoir will get very full on drives. The shorter the drive the less full it gets. The longer the drive the reservoir can get 100% full and fill all the way up to the cap. After cooling down the overflow flow reservoir goes back down to a normal level. I think on long drives the coolant leaks out of the top of the overflow reservoir until the coolant gets low enough to cause the engine to over heat. When I put more coolant in the radiator everything runs great. What is causing the over filling of the overflow reservoir? Is it a cracked head/head gasket even though all my testing says it's not? Could anything else cause the over filling of the overflow reservoir? Should I try a head gasket sealer (if so which one do you recommend)? Is there a way to check if the radiator is clogged internally or if there is a clog somewhere else in the system? I will be pressure testing the radiator and radiator cap next as well. Any advice would be greatly appreciated. Thank you for the help and the video. | |||||
| RE: Milky radiatior... | 16Relevance | 3 years ago | nlord | Submit Your Question HERE | |
| If somebody mixed the coolant, and it was actually the old green stuff that does not play nice with other types of coolant, I would think it would happen fairly quickly after it was added. Did you just happen to check the coolant, or was the car having issues? I would also check your oil, and your transmission fluid and see if they look funny. As was mentioned, blown head gasket could be an issue, also there is a rare issue of the radiator corroding and mixing the transmission fluid with coolant, that will make the coolant look milky and often pink due to the transmission and coolant color. That issue is often deemed the pink milkshake. For whatever the issue, you want to act quickly to resolve the issue would be my suggestion. | |||||