Notifications
Clear all
Search result for: evans coolant
| # | Post Title | Result Info | Date | User | Forum |
| Blown head gasket? | 16Relevance | 4 years ago | AVI2020 | Submit Your Question HERE | |
| Year: 1992 Make: Subaru Model: Loyale Miles: 250,000 Transmission: Auto Hello everyone I need some help. I was driving this car today. Everything ran great. Whenever I use the AC the engine temp is good on the highway but in the city would rise a bit and I would shut it off. Been like that for a while (I guess the radiator cooling fins are dirty). Came back home and saw smoke coming out of the left wheel well and heard a sizzling noise. Pop the hood open and noticed the coolant tank was a bit "inflated". The fluid level backed up to the top and build up enough pressure to leak past the coolant tank cap. The worst part is the color of the coolant in the radiator and coolant tank went from green to brown. I think oil mixed with the coolant. I hope it's a blown head gasket and not a cracked cylinder. I think Old Bessie (the station wagon) is dying 🙁 My dad blames the thermostat building "too much pressure" but I do not think that's the case. Otherwise, the engine would overheat and not cool. one more thing. I contacted a mechanic to have it looked at. Would it be best to change oil/filter, and coolant to make a 10-mile trip? Just to prevent any premature bearing damage. Thanks in advance | |||||
| Answer to: 2008 Toyota Highlander very intermittent vapor or smoke under hood | 16Relevance | 4 years ago | Justin Shepherd | Submit Your Question HERE | |
| It's more likely your 14-year-old heater core and radiator hoses are weeping coolant. This would only be possible if it were really cold. Once the car warms up, the outside temperature means nothing. The coolant is at 192 degrees when it's fully warmed up, the steam indicates it's hot. 2-4 degrees difference in ambient temperature isn't going to make rubber seals expand or contract that much. -60 degrees may, but not within that kind of range. Flex the heater core hoses and look/ feel for seepage when the engine is cool. Most likely you have a crack that weeps when the pressure in the line varies, and the hose flexes. Also replace your radiator cap. They wear out and can cause slow evaporation of coolant. | |||||
| Answer to: Normal Operating Cooling Temperature | 16Relevance | 4 years ago | Nathaniel J. | Submit Your Question HERE | |
| Yeah! Thank you, I’ve looked for all the signs of a bad water pump, there is no coolant leakage under the vehicle and I’m not losing any coolant. So I don’t believe the water pump is bad. I’ve been told signs of a bad water pump, are a white milk ish residue on the top of your oil cap, coolant leaking from the weep hole from your water pump, lost coolant for no apparent reason,, and overheating. I haven’t seen any of those symptoms. The only reason I took it to the shop is because it was running hotter on normal operating temperature. And I’ve checked the coolant levels and I replaced the radiator a month back to try to make it run cooler; and it didn’t fix anything. But I made sure the coolant was topped off and everything looked good. | |||||
| Answer to: Hyundai screwed me over with a bad engine and I'm not sure what to do | 16Relevance | 4 years ago | Donjones95 | Submit Your Question HERE | |
| Update: Hello all, I wanted to provide an update and ask for advice on next moves. So, TL:DR: Hyundai screwed me with a bad engine. Talked to corporate, Atty. Gen., warranty company, attorneys, etc. Everybody told me to kick rocks. I have $1k+ and I need to get rid of this car ASAP. A mechanic told me to try Blue Devil and I bought it (requires thermostat removal, not pour and go.) Haven't used it yet. Need suggestions on what to do. Basically, 2017 Hyundai Elantra had engine replaced. There's a pinhole leak in the throttle body coolant line that goes to the engine, causing it to overheat. Head gasket blew. The coolant is orange from mixing with oil, though the oil is clean, so best guess is there's oil in the coolant, not coolant in oil from what I can tell. I was recommended a shop by a friend who owns a dealership where he gets his cars fixed. I was told by the mechanic to try blue devil gasket sealer, which I have sitting in the garage (it's the original one that requires the thermostat be removed and the cooling system flushed at least twice. Not the pour and go.) They told me to try that, and if it didn't work they could find out about putting a new head gasket on. I haven't tried it for two main reasons: 1. I'm kind of worried about it gunking up important parts. I've heard people swear by it, that they've had blown gaskets, warped engine blocks/cylinder heads get up and working with it, and I've also head a lot of mechanics say it's a LAST resort as it usually will gunk up things like the heater core, coolant lines and so forth. 2. It's been difficult finding a mechanic that will do it for liability reasons, and I don't have the tools nor know-how on how to take the car apart, remove the thermostat, flush the cooling system and accurately do everything without screwing it up myself. The service manager at the dealership told me that it would likely take a new throttle body and hoses to get it running again, although I don't think a car is gonna run much with a blown gasket. I don't need/want a permanent fix, I'm trading it in immediately (have a guaranteed offer on the car once running.) What can I do to get it up and running for me to trade the car in? I've done EVERYTHING: Spoke in-depth multiple times with both the dealer that sold me the car, and the dealership that did the work (I was offered 10% off repairs. Woopee.) I contacted Hyundai corporate (I was told the engine's warranty ran out, and that it didn't cover the new engine. Tough luck.) I contacted the AG in my state (they contacted Hyundai corporate, who gave them the same answer they gave me, and refused to do anything.) I also contacted lawyers about filing suit (it would cost more than I would gain and no lawyer would take it on.) At this point, I just need to get it running so I can get rid of it finally. Sister is giving me $1k to do whatever I can to get it going to get rid of it. Any suggestions? I've attached pictures of the engine bay. The rust colored stuff is the coolant. Thanks! | |||||
| Answer to: 2011 Nissan Frontier Engine noise diagnosis | 16Relevance | 6 years ago | geriscan | Submit Your Question HERE | |
| There's a lot of different things going on here, and it's very hard to separate cause (or causes) from symptoms because of the complexity. So, what we do know, from your narrative, is that you're losing coolant. Sometimes coolant loss can come from a leak close to or around the intake manifold, which, when the engine is running, is so hot that it evaporates the coolant. (So, you never see it) You might have a coolant line or lines that are brittle and leaking. So, you should check for that. In fact, it would be wise to very carefully check all the hoses going in-and-out of the engine. as well as any gaskets (including the thermostat gasket) that funnel coolant inputs and outputs to and from the engine. If there's a coolant leak from hoses or fittings for hoses, that would obviously affect the water pump. Parenthetically, if there's compromised hoses, I doubt that K-Seal would be useful. You can run a very simple block tester on the radiator to determine if there's combustion gases in the engine. Scotty has videos showing how this can be done. (See the bottom of the post). ___ Clean the Mass Air Flow Sensor. It's easy and cheap to do. Scotty has a video on that, as well. (See the bottom of the post). Also, as easy and cheap, you should also clean the throttle body. __ Now, if the 02 sensor is bad, it will make an engine run rough (and play havoc with the 14.7/1 ratio of air to fuel). There are ways to test an O2 sensor. Google it. You'll find tutorials. And, if you have a decent OBD II scanner that can check for problems with the cat, do that, as well. (Usually, you'll get a P0420 code). __ Obviously, the vehicle might benefit from a fuel injector cleaning. (Scotty has a video on that, as well). Erratic spray patterns will give the ECM and engine fits. __ Scotty usually advises to start simple and cheap. Do the obvious things first (like very carefully looking in-and-around the hoses and inputs and output of the engine and the intake manifold) which is what I'm suggesting. If you do the simple things systematically, you'll eliminate possibilities and then what remains becomes what it must be. (It's very much like detective work). Keep a log of what you're doing, in case this does eventually go to a diagnostically-oriented mechanic. I spent nine years in Massachusetts, in places like Lowell and New Bedford. I know what a beating a vehicle takes during a New England winter, particularly along the coast. Good Luck. | |||||
| oil in radiator - Vortec 5.3 LM7 | 16Relevance | 6 years ago | capikrad | Submit Your Question HERE | |
| Hi. I have Chevy Express 2007 AWD with Vortec 5.3 LM7 engine. I have found oil in coolant - milky stuff below radiator cap. I discovered that mix oil-coolant comes from little tubing which goes from the engine head to top of the radiator. I dont see any coolant in engine oil. I didnt experience overheating, engine codes or excesive or low oil pressure. Nothing. Van was driving OK - I guess I just have found it before it could make a mess. My question is what could be the issue: 1/ transmisiion cooler - maybe it is transmission oil in coolant but why I see oil/coolant mixure enetering from the tubing which goes from cylinder head? 2/ blown head gasket - how to verify that? I did combustion leak test (suck air from top of radiator and checking if testing fluid goes from blue to yellow) with negative result. Seems the head gasket is not blown in cylinder area. Could be head gasket blown in oil passage only letting oil to enter coolant? How can I verify that without removing the engine head? Thanks for any opinions/advice. | |||||
| 94 Toyota 4 Runner (3.0 V6, 3VZE Automatic 4WD) Head Gasket Maintenance and Electrical Issue | 16Relevance | 6 years ago | Lexus_4Runner | Submit Your Question HERE | |
| I have 2 questions on my 94 Toyota 4runner SR5 4WD Full Option Truck. in is a 3.0 V6 (3VZE) I've heard you say that early to mid 90's toyota 4 runners are good but wanted to double check. Little background. My 4Runner has 177,000 miles but the engine only had 48,000. Toyota installed a Reman engine 7 years ago after the original engine blew a head gasket and pieces of the head gasket fell inside the cylinder and caused damage. I later had an issue where coolant was dissapearing 10,000 miles ago and Toyota had to replace the head gasket again on the reman engine. I have to say the second time the engine did not over heat or anything but I was not watching the coolant as meticulously as I do now. The second time the head gasket seemed corroded. Toyota told me that if I should have changed the coolant every 20,000 miles to prevent this corrosion and I was like ...."Why didnt you recommend to me and change the coolant?...This is why I bring it to you and no one else" The bill the on the second head gasket repair was $3000, but I did get the timing belt, Water Pump, idler pulley, thermostant and a some temperature sensors all replaced for the price by the Toyota dealer. I have heard the 3VZE has a design flaw on the intake manifold that causes headgaskets to blow. If you believe there is a design problem how serious a design problem is this? Should I sell the car? Is there anything I can do to prolong the life of the head gasket if you think I should keep it? I do watch the coolant like a hawk every week and will replace it every 20,000 just to make sure the anti-corrosive chemicals in the coolant dont get too weak... The car runs like new except for an electrical problem I am about to mention below. My cousin and I both (mechanical engineers) who owned this car have maintained this car well with over $26,000 of Toyota Service records over 26 years. At this time the car runs really well mechanically except for a "groning" sound the first couple of miles on a day colder than 25 degrees. Who knows what that is but it doesnt bother me too much...would still like to know what that could be.... Now to the electrical issue. When I have the AC on with the lights and run it around town for an an hour or idle it for 30-40 minutes, I am down at 12.2 ish volts on the battery. On hot days I got stuck around town which is why I took it to the dealer. The dealer replaced the idler up system, went thro two batteries and 3 alternators - the last laternator being from autozone reman lifetime warranty. I spent 950 bucks and the problem was not solved. I had a one on one with the service manager and got my money back. The alternator I originally had on the car was an original toyota nippon denso. I did not ask them to put in an autozone duralast china alternator but they suggested I do it because Toyota alternators did not resolve the issue. They said all the relevent wiring on the harness checked out good. Now, in addition to the charging problem I originally had the Chinese Duralast lifetime warranty alternator installed by Pueblo Toyota is squealing when turn the lights on. When I turn the flashes on squealing gets "louder" and "softer" in synch with the flashing. So while they have given my money back since they couldnt figure out the charging problem, I now have inherited a new squealing problem with this chinese toyota bought and installed duralast autozone alternator. I only have a 300 miles on this alternator. Toyota now wants to charge me another 500 bucks to give me back the alternator I originally had (Reman Nippon denso from Toyota). What do I do. Yes, toyota did give me the money back because they could not fix my charging issue but they've created a chinese alternator squealing issue for which they now want to charge me. What do I do? Any thoughts on what this electrical issue is? Car does fine when I just have the AC on without the lights, or just have the lights and blower on without the AC button pushed it. It also does fine when have the lights and AC on and drive on the freeway or over 55 mph. The problem comes when I idle or drive around town for an hour with the AC on and the lights on - the voltage at on the terminals sprirals down in a downward cycle and goes down to 12.1 volts in 40 minutes. It is still a nice car though....what do I do. I'd like to have it since we are now in Colorado and I'd like to have this 4WD. Thanks very much. | |||||
| Answer to: 2020 Subaru Impreza antifreeze level at low line | 16Relevance | 6 years ago | Dion | Submit Your Question HERE | |
| I dunno..your car is under warranty and any issues that come up and not using non-authorized approved factory coolant is iffy in my book. If something is going wrong...and losing coolant is a hint...you come in and they detect your using Wally coolant...they could deny your warranty claims....I would buy the factory coolant to keep it safe. I don't put it past any dealers to try his stunt. It's on you however but I would go with the approved factory coolant and KEEP every receipt to insure your NOT denied in any way. Another way is ask the dealer if coolant non-factory brand is approved and get that in writing. I would like to hear their reply. | |||||
| Answer to: Ford Taurus Blend door question | 16Relevance | 6 years ago | jack62 | Submit Your Question HERE | |
| So it seems you're "chasing down" 2 suspicions. 1) is hot coolant circulating through the heater core? 2) Is the Blend door operating? Both are easy to determine. 1) is hot coolant circulating through the heater core? If you look on that Taurus, between the engine and the firewall you'll see a hose/metal tube unit. It's a "one piece unit." A "confabulation" and abomination of flexible hose, "factory joined", with metal tubing. Probably looks something like this: So with the Taurus, a large part of this unit sits very low in the coolant circulation system and any "sludge" tends to settle there. So, is the coolant circulation through the heater core? Tools required: 1 hand. Feel the hose going into your heater core and the hose coming out. Both should be hot. OR, Is this an issue with the blend door? Drop the actuator. (pop out the back of the glove compartment box and you can access the screws on one side and then get the other one from the driver's side.) Maybe 5 minutes. With the actuator in your hand and connected, when you change the heat/cool setting does the actuator spin? OK, digging deeper. Why did you find brown sludge in your cooling system? If memory serve me correctly that Taurus used an HOAT (Hybrid OAT) coolant.(Yellow) That can't be mixed with IAT (Inorganic Additive Technology) coolant. If you do that it creates sludge. I think a previous owner did that | |||||
| 2004 Blown Head gasket--rapid collant leak after i hit pot hole | 16Relevance | 6 years ago | Danny1 | Submit Your Question HERE | |
| Great videos! Super clear video on steal seal gasket repair. Ford Taurus 2004 hit pothole and then all coolant from reservoir leaked out (not sure of if radiator is depleted). Engine smoke with white under hood as i drive but temperature rises but have not reached danger red zone yet sine ib constantly add water and made only short trips. Mechanic said it was a gasket leak. Very rapid/smokes after 4 minutes driving and loss of coolant rapidly as i add it with engine off.. The leak is right under the water pump but mechanic says pump is ok --mechanic says no way a pothole could cause gasket leak.. Is that true? The leak is right near wheel that hit the pot hole and I felt engine move. May have had small gradual coolant loss before. Main question: My leak is to rapid for sealer to work I fear, but have not tried it yet. If leaks spews out coolant as I add it, can I lift up the car on right side to slow leak before starting to give enough time to gasket repair like k-seal or Steel seal to work? It seems to suck up more coolant upon start however but smokes after 4 minutes. maybe cold weather may help with delaying overheating from rapid coolant loss as run it to cure sealant). Another novice/ hair-brained idea: Could I use silicon gasket maker such as JB Weld high heat epoxy on outside of leak to temporarily slow leak enough for gasket sealer to work (15 psi will likely push that out quickly but maybe give me time)? Should I consider fiber reinforced Bars or k-seal or silicone dioxide based products for faster sealing/curing repairs for rapid leaks. Any product recommendations or ways to deal with rapid leaks for 2004 taurus? | |||||
| Upper coolant hose came off when I was parking my SUV . Did this come loose only because of friction/vibration or could an over-pressurized system blow a coolant hose loose? | 16Relevance | 5 years ago | jsinanis | Submit Your Question HERE | |
| 2002 Toyota Sequoia Ltd. 199,530 miles Automatic Very confusing scenario, because I changed my thermostat a few weeks ago and I do not remember removing my upper coolant hose. Anyways, last night, as I was parking my SUV on a bumpy incline, a bunch of steam is spewing out of the hood. I go to look and the upper coolant hose is sitting completely off the radiator. Could there be some erroneous issue I should be aware of? Like a clogged overflow tank? I would like to rule out any stupidity before I fill my coolant again as I lost a lot in the 10 seconds it came off and was running | |||||
| 1995 Maxima coolant reservoir losing coolant | 16Relevance | 6 years ago | Mark217 | Submit Your Question HERE | |
| So I got an issue with my 1995 Nissan Maxima with 166.5K miles. Car runs great, doesn’t overheat and the radiator is always full of coolant. However, the reservoir loses coolant. I would fill it to the full mark, then after 2-3 weeks it would be a little bit left in the reservoir below the minimum mark.I would leave it (not refill it) and the small amount of coolant will remain in the reservoir and still not overheat. Radiator remains full as well. The radiator and both radiator hoses were replaced last summer, so I don't think those are leaking. I’m thinking either the reservoir is leaking or it’s leaking from the hose that goes from the radiator to the reservoir or leak from both. Any help is appreciated. | |||||
| 07 Avalon coolant burning | 15Relevance | 10 months ago | Finer_Things | Submit Your Question HERE | |
| Hey Scotty, I have an 07 Toyota Avalon with the 3.5L 2GR-FE engine, and currently has 217k miles. At around 190k miles I noticed that the coolant was emptying, and noticed that I can see smoke coming out of the exhaust even when it's at operating temperature. I took your advice and put some K-Seal coolant leak fix in it, and got some 30k miles of relatively trouble free driving. I have checked the coolant occasionally since then, and only recently did I notice it really starting to get low again. I can see it burning out of the exhaust and can smell a sweet smell. I don't have any oil dilution or any other sign of a coolant leak that is visible to my naked eye. It doesn't even leak or burn any oil in between oil changes either, and it looks perfectly normal every time I change it. I also can't see anything leaking on the ground where I park my car at home. What risk do I currently have of it diluting my oil and destroying my engine, and is there anything more I can do to extend it's life? Could I try another bottle of K-Seal? Or do you have any other suggestions? | |||||
| RE: Should i top off coolant or do a flush? | 15Relevance | 2 years ago | Justin Shepherd | Submit Your Question HERE | |
| @imperator Thinking about it again, there's no way you could make a thermostat watertight. The impeller sucks coolant through the radiator's bottom hose, as well as coolant that was already circulating in the water pump itself and pumps it into the block to be heated up. If the thermostat hasn't opened up yet, it bypasses the radiator and goes back into the block in a "shorter" circuit. There would almost be a vacuum if it sucked all of the coolant out of the lower radiator hose and the t-stat were watertight. I couldn't remember if the coolant expanded significantly while still liquid, or not. I was kinda reaching the end of my easily disposable knowledge (I woke up like 20 minutes before replying). I kinda didn't realize until your response that the hot liquid's expansion is quite significant. Hot liquid+the same space=higher pressure. I've only ever opened a radiator when the car has sat for a few hours, because subconsciously know the risk of opening one when it's still hot. I tried to imply that in what I wrote earlier, but I never directly stated it. My apologies. | |||||
| Answer to: Should i top off coolant or do a flush? | 15Relevance | 2 years ago | MountainManJoe | Submit Your Question HERE | |
| the system is pressurized by the expanding water, not the pump. The thermostat is not a perfect seal. In fact some have a tiny relief hole to allow air to escape and pressure to equalize ("wiggle pin"). Even if it was perfect, the radiator is not sealed at both ends, so the pressure is equal everywhere. On modern system the thermostat is downstream of the radiator, right before the pump. Water pumps are of a centrifugal design and move fluid, not pressurize it. you should never open (or open very carefully) the radiator when the engine is hot. Even if your pump is completely failed, the radiator will be pressurized when the engine is hot. This isn't always the case. it's nothing to do with the elevation. pressure moves the coolant to and from the reservoir. Attachment : thermo.jpg | |||||