Notifications
Clear all
Search result for: evans coolant
| # | Post Title | Result Info | Date | User | Forum |
| Answer to: Overheating and coolant leak | 15Relevance | 1 year ago | Chuck Tobias | Submit Your Question HERE | |
| If you are seeing coolant come out from between the engine block and oil pan there is something seriously wrong going. Unless that thing has a really wacky design coolant should not be present there. Possibly a blown head gasket, cracked head or block, maybe a liquid-cooled oil cooler if so equipped would let coolant get into the oil. I'd try to get eyes on where the coolant is actually escaping to verify what's going on. It's not worth putting a lot of money into 16-year-old VW. (Kelley Blue Book pegs the value of that car in good condition in a private party sale at about $3800, and their estimates tend to be on the inflated side.) | |||||
| 4Runner coolant level drops | 15Relevance | 2 years ago | Scottydaman2023 | Submit Your Question HERE | |
| 1996 Toyota 4 Runner 2wd 302k miles Aloha, car runs great. But started noticing coolant levels in radiator are low, no where near top. I started filling it up, topping it off. And after a few days the coolant resrovir was overfilled, but i was adding coolant directly into radiator. After that coolant level on radiator still wasn't on top, was pretty low. I'm confused. | |||||
| Answer to: water pump leaks coolant | 15Relevance | 3 years ago | Justin Shepherd | Submit Your Question HERE | |
| Shortly before I knew I had brain cancer last year, my Ranger blew a coolant hose while I was getting on the highway. coolant poured out of the truck, to the point where a rooster tail was coming out of the hose, not white smoke. Aound 2000 feet past the on-ramp I pulled over and immediately shut off the engine.. I had set the heater to just barely over neutral a few minutes before. The plastic had become so embrittled, when I went to accelerate enough to get on the highway, the plastic gave out. I lost half of my coolant in around one minute. There's still a coolant stain on that stretch of highway where I had broken down almost a year later. Haha. | |||||
| RE: Coolant intrusion in my 4yr old Ford Ecoboost! | 20Relevance | 4 years ago | Jonnyboy57 | Submit Your Question HERE | |
| Scotty - there is a class action lawsuit in place against Ford and the coolant intrusion problem. They already have a technical service bulletin out for it. They know it’s an engineering flaw . Can you do a video and maybe some Clickbait on this to bring a higher level of visibility to it? By the way I’ve come up with a short term solution to minimize the coolant loss and triggering of the misfire fault. If after you get done driving it you unscrew the coolant reservoir cap and let the pressure off no coolant leaks into the cylinder. It seems logical to me if you take the pressure off of it there’s nothing to push the coolant in through the crack. This seems to highly minimize the amount of coolant you consume. Not a fix but a Band-Aid . Please Scotty make a video and make a big deal about this issue. Ford should be replacing these blocks for free. Thank you love the channel | |||||
| 2008 Mercury Grand Marquis Coolant Flush | 20Relevance | 4 years ago | Lahito-1997 | Submit Your Question HERE | |
| Hello! I had yet another question about my car as since I’ve done a bunch of work on it there are a few things I couldn’t really get a straight answer to like a coolant flush on my car, I just recently drained the anti freeze out of my car and replaced it with only distilled water *I did not flush the coolant that is in the engine block* and a cleaning agent to clean up the debris in there however something that I wasn’t too sure about is, with the cleaning agent should I take out the thermostat for the time that I run the engine with the cleaning solution or is it no problem to leave it in, along with another question is when I do flush the system out how would I get the remainder of the coolant out of the engine as to my knowledge a simple opening of the petcock drain doesn’t get rid of all the coolant from system, I live in NY and want to ensure that the coolant to water ratio isn’t off significantly from the 50/50. Edit: I know that I could look at videos on YouTube however the issue is they show a simple flush by opening the drain and then refilling the system with a mix they don’t remove all the coolant from what’s left in the engine block. | |||||
| Answer to: 2004 Honda Civic Hybrid Coolant leak milky residue | 20Relevance | 4 years ago | czi50agjb8wa | Submit Your Question HERE | |
| It was being driven daily for weeks so it wasn't condensation. Unfortunately, the radiator had an internal leak so the CVT transmission oil & coolant had mixed. The pressure didn't drop when there was coolant, but I heard a hissing sound from a relief hose on top of the transmission as I was pressurizing the radiator to force more coolant to drain. Checked the transmission oil dipstick, found milky residue on the tip + oil was nowhere on the level. Verified coolant was in transmission when it drained first then turned into chocolate milk 🙁 Removed heater core outlet hose & milky residue came out. It was never driven after we heard the noise & it leaked on the ground. What can I do to improve my 50/50 chance odds of salvaging the car? Plan of attack: Remove the thermostat & flush with a garden hose & back flush the heater core. As much as I don't want to use hard tap water, I don't really have a choice if I want to rinse it out of the cooling system. Replace the radiator. Use distilled water & coolant flush solution. Use the used transmission oil to temporarily fill & rinse off the milk chocolate sludge. Drive it about a week, then drain & fill the coolant & transmission oil, cross my fingers & see it that'll fix it. Just recently replaced the hybrid battery so junking it isn't an option either 🙁 With the inflated prices of cars right now, it was a calculated risk. Worst case scenario is the transmission's shot as well, but one landmine at a time. | |||||
| 2004 Civic hybrid coolant mixed with CVT fluid and chocolate milk in tranny | 20Relevance | 4 years ago | czi50agjb8wa | Submit Your Question HERE | |
| Hi, Mr. Kilmer, I have a 2004 Civic Hybrid 1.3L 153k miles CVT that fluid sprayed around the area below the battery. There was a gargling slight screeching sound around the drive belt area (probably the water pump). Turned it off immediately. Checked the coolant in the radiator & it wasn't topped off as usual + found milky substance around inside the radiator tip & cap. Was scared that it could be a blown head gasket, so I checked if the engine oil cap & dipstick, thankfully it was normal. Rented a cooling pressure test kit & pressurized the radiator to 16psi to see if it would leak, but nothing, no pressure drop. The leak only showed up when the car is running & it was overflowing from the coolant reservoir & turned it off ASAP. When I opened it, it was like it was frothing milk not the normal blue fluid. I then tested the cap which wasn't holding pressure so I verified it was defective. I get how it leaked, but I don't understand why it became milky. I've always read that it's from coolant & oil combining, but if the engine oil wasn't milky, it didn't overheat, & there's no white smoke from the exhaust, can it really just be a simple radiator cap replacement fix or do I need to worry about replacing the reservoir cap as well even though it was on tight? I don't see any cracks on the reservoir. It was only a couple of seconds after starting that it starts leaking (from cold engine) so how can it generate that much pressure to come out the reservoir cap frothing? Shouldn't it still be blue? Or was the milky substance just from starting it during the cool early morning temps? I topped the radiator with a little Prestone 50/50 coolant since I couldn't see it from the top of the radiator. Should I also do a block leak fluid test? Do I need to drain & fill it with new coolant before that or should it be done as is? If the block test isn't necessary, do I need to completely replace the coolant or will it turn back to normal by itself? Thanks. | |||||
| Coolant temperature fluctuation | 15Relevance | 3 years ago | wretchasketch | Submit Your Question HERE | |
| I have a 2005 Buick LeSabre custom with the six cylinder 3.8. It has a temperature gauge, and the needle sits right in the middle during vehicle idling an operation. It also has a coolant temperature reading on the dash, which fluctuates between 188° and 210°. Next to the coolant temp, it always says “normal“. The fluctuation in coolant temp doesn’t affect the engine temperature gauge. Is it normal for the coolant temperature to fluctuate that much? The level checks OK. Should I be concerned that either my radiator, cooling fans, or thermostat is not working optimally? | |||||
| Answer to: Subaru legacy 2009 coolant color | 15Relevance | 3 years ago | Kevin1527 | Submit Your Question HERE | |
| Do you know if is necessary remove the coolant from the engine block to change the coolant or just changing the coolant in the radiator is enough? I’m looking for some tutorials to remove the coolant from the engine block but I didn’t find anything that can help me. | |||||
| Answer to: Ford Mustang A/C system and coolant leak | 15Relevance | 3 years ago | Justin Shepherd | Submit Your Question HERE | |
| Your coolant and refrigerant are completely separate systems. Why do you have a coolant leak? Get a coolant compatible leak dye and try to figure out where it's leaking. There's really only 2 ways coolant can leak out, either the hoses are bad, or you have a head gasket leak. You could also have a bad radiator cap. If you heard it leaking from inside the car, most likely it was the refrigerant leaking. Check the condenser, it's in front of the radiator. The refrigerant is under high pressure and can easily generate noises if punctured. There will be PAG oil of if that is indeed the problem. | |||||
| Why is my car losing coolant? | 20Relevance | 5 years ago | Hyundaidriver | Submit Your Question HERE | |
| I have a 2011 Hyundai Equus ultimate package with 124,000 miles. A few weeks ago I refilled my power steering fluid and noticed I had almost no coolant. My car doesn’t have a coolant sensor and my vehicle wasn’t showing any signs of overheating so I had no idea. I topped off on that too and a week later I checked again, the power steering fluid stayed the same but the coolant was down to the half way point. I figured since it was almost empty before, the coolant loss was just due to it cycling through. I topped it off again and then 2-3 weeks later I decided to take another look and now it’s almost empty again. The car isn’t leaking anything from the bottom, I removed the skid plates to check if there was any evidence of a leak, still nothing. I suspected an internal leak so checked the radiator/radiator cap and the water pump, still nothing. I’ve looked at everything in the engine bay and the exhaust, its completely dry. The car isn’t driving abnormally, making noises, producing abnormal vapor from the exhaust or overheating. I genuinely have no idea where the coolant is going but since so much Is disappearing in a short amount of time, it has to be going somewhere. | |||||
| 2009 Hyundai Sonata coolant gauge going up | 20Relevance | 5 years ago | notsureman | Submit Your Question HERE | |
| Hello again, I'm back with another question. While working doing my delivery's today I noticed every time I idle for more then two minutes my coolant temp gauge starts to go up, went to 3/4 then a little past that then came back down. I checked with my scan tool and the highest my coolant temp was 199.4F, at that time my fan came on and it started going down then I started driving again. Gauge came down but was still almost 3/4 but scan tool showed coolant temp as 181F. I checked for leaks, none that I can see. Fan is working as expected, coolant level is just below the full line. No check engine codes. Is it possible the cluster gauge is acting up? I read about adding another ground to the battery to potentially fix cluster gauge problems. My cluster gauge does already have problems, my fuel is always off/sticking. Any specific things I should check? I'm gonna start with the ground, then probably move on to coolant sensor/thermostat. coolant is new btw, well was done about 20k miles ago. Edit: Car has 179k miles, has the 2.4 engine. | |||||
| 2007 Mazda 3 2.3L Coolant Leak Fixes itself? | 20Relevance | 5 years ago | Bm3 | Submit Your Question HERE | |
| Alright so basically I had my car stored in a garage for 10 days. after 10 days, I decided to give it a good 15-20mins drive to warm it up and make sure that everything was good. While I was driving, everything was normal (car had heat, temperature was normal) As soon as I pull up to my driveway, the car started to sound like it had an exhaust leak. I checked under the car and that's when I made this video of the coolant leaking from the Botton (bare in mind that the car was still on when this leak was happening) I then decided to store the car in the garage for another 10 days and fix this issue later. 10 days later, I called my mechanic in and he saw that the coolant reservoir was still holding coolant. He then topped off the coolant that had leaked out and started the car. No leaks, whatsoever. He kept it on for a good 30 mins to see if there were any leaks at idle. Then, we went on a good 25 min drive and again no leaks. Once again, everything was normal during the test drive (the car had heat, coolant seemed to be circulating in the system, temp was fine), and no leaks. coolant Reservoir level didn't drop. What could the cause be? could it be just a stuck thermostat? hose? btw, the climate out here in Canada is cold as well so could that have impacted it? | |||||
| Answer to: Coolant System Flush vs Drain | 20Relevance | 6 years ago | Conal Lane | Submit Your Question HERE | |
| As has been said, a regular drain and fill will extract quite a lot of the old coolant. The thermostat problem is solved by getting your vehicle up to operating temperature and turning on the heat. Depending on the vehicle the thermostat valve might be quite accessible and it's just a couple of bolts to remove (mid 2000's VW were not at all accessible) I can only speak from my own experience of a flush with distilled water, as I was changing from the Ford Motocraft antifreeze over to the Green Prestone universal about a year ago. 1. Remove the radiator cap if your car is fitted with one, and remove the cap of the expansion tank. 2. Drain the radiator via the drain tap or bottom radiator hose ( this will extract about 40-50% of the coolant) 3. Refill with distilled water, run your engine with the heater on full power and high heat for about 10 minutes to allow the water to circulate. Drain again as in step 2. You may repeat these steps once or twice more until the radiator drains clear water. 4. Refill with coolant, and run the engine again for about 10 minutes or so, this time with the expansion tank cap removed to allow the system to belch out any air pockets. 5. Keep an eye on the coolant level over the next 5-7 days and top up to the fill line if necessary. My '07 Focus takes 7.3L of coolant, and me being the slightly nerdy type I measured the amount of coolant drained and it stood at just shy of 7.3L so in my book that's as good as a compete flush as is possible. Note that I'm located in Ireland, so I have the advantage of a moderate climate, neither extremely hot or cold. I would recommend to do this process on neither a very warm or very cold day as your engine will temporarily at least be using plain water in it's cooling system. Hopefully this might help you. | |||||
| 2010 Audi Q5 3.2L Coolant leak | 20Relevance | 6 years ago | MickVet29 | Submit Your Question HERE | |
| ... Audi Q5 Prestige trim level. I know what you’ve said about Audi, and I did my research for a long while. I purchased it cash, as I did my wife’s 2014 Buick Enclave. Since purchasing my Audi, I have driven it to and from Columbus, Ohio and to evansville, Indiana (my son plays travel hockey) and back. No issues. I had the 90,000 mile services done where I had my local shop change the oil and filter, I furnished the supplies. While in evansville, I bought the G-12 coolant for it because the shop said the coolant was just a touch low. The vehicle doesn’t overhe ... | |||||