Notifications
Clear all
Search result for: evans coolant
| # | Post Title | Result Info | Date | User | Forum |
| Answer to: Can the temperature gauge rule out a bad oil pump? | 22Relevance | 5 years ago | Justin Shepherd | Submit Your Question HERE | |
| Not necessarily. The thermostat measures coolant temperature, not oil temperature. Lack of oil will cause the engine to heat up, but it won't necessarily lead to overheating (hitting H) being measured via the coolant. You may or may not notice coolant temperature being slightly hotter due to the way the engine is cooled and lubricated. Low oil pressure will cause noise due to metal on metal contact in the engine. The engine will stop running in an oil starvation situation because bearings, rings and seals fail quickly without the oil due to the friction. This does overheat the engine, but not in the same way as lack of coolant. Lack of coolant causes the heads, head gasket, engine block, etc. To fail. Lack of proper lubrication and oil cooling causes more localized things like the end cap bearings, crankshaft/crankcase bearings, wrist pins, timing chains, rings, cams, etc. to overheat. These things are directly lubricated and cooled by oil, not coolant. coolant flows through the block and takes heat from some of these things through the cylinder walls and coolant jackets, not by direct contact. More modern vehicles like my 2017 Mustang have an oil temperature thermometer in its digital instruments as well as an oil pressure sensor. If you hear metal on metal sounds like tapping, knocking, scraping noises, etc. you definitely have an oil pressure problem. Get an oil pressure checking tool and manually check the pressure with the engine running. That will lead you in the right direction. | |||||
| Answer to: 3.8l Caravan coolant boiling or bubbles in plastic coolant recovery tank | 16Relevance | 2 years ago | Hixster | Submit Your Question HERE | |
| The bubbling air means air's in the system. A bad cap will make your system have low pressure, which can cause coolant loss. If you have no coolant mixing with oil or vise-versa then get a OEM cap. Pressure testing the coolant system will reveal if you have some other leak. New cap would fix it , if that's the leak. | |||||
| I lose all coolant in 100 kms with the AC on & there’s oil in my coolant too | 16Relevance | 5 years ago | Faisal haroon | Submit Your Question HERE | |
| Toyota rav4 model 2012 Japan made with 172000km. I am facing a problem there is small amount of oil in coolant of radiator. Mechanic are not sure whether it is from gear oil or engine oil. It just stay on the surface of coolant. Second issue my car decrease the complete coolant reservoir at journey of 100km. There is also no leak. It only happen when Ac is working. Without ac it stays same for a long period of a month. Any one can trace out from given information. Thank you in advance | |||||
| Answer to: '06 Mazdaspeed 6 Power Loss, Sputtery feel in Acceleration | 22Relevance | 6 years ago | Razmig Bartassian | Submit Your Question HERE | |
| @joshhuckOh, so not that much coolant came out. So for bleeding the cooling system, you start your car up with the heat on the max setting WITH the reservoir cap off. This will have the car warm up quickly to open up the thermostat. When the thermostat opens up at operating temperature (when gauge is about halfway), the coolant will start to flow throughout the whole system, and this will help carry out any air bubbles out to the coolant reservoir. You then want to rev the engine up to like 2k rpm a few times so the water pump stimulates more coolant flow. After about 5 minutes, check the coolant level. If the level went down, then it means you got a good amount of air out of the system. If the level didn't change, then there wasn't too much air to begin with. You can now close the coolant reservoir. You want to make sure you feel a good amount of heat coming out of the vents, but if there isn't then it means there is a whole bunch of air stuck in the heater core that still needs to be released. I wouldn't worry too much about any trapped air since hardly any coolant came out. This process is generally for a full coolant flush. | |||||
| Answer to: Coolant in all 4 cylinders from cracked coolant hoses | 21Relevance | 3 years ago | Justin Shepherd | Submit Your Question HERE | |
| coolant doesn't flow by the ignition coils. That would possibly short them out. Any time your vehicle overheats, your head gasket is put under tremendous strain, and it's only a thin piece of aluminum that seals the space between the heads and block of the engine. It's flimsy, and breaks extremely easily, especially when you have active combustion going on, on the other side. In all honesty, you should have stopped right away when you noticed your car was overheating. The upper or lower radiator hose was still leaking the entire time you were driving it, which means you were still losing coolant. Driving it 5 miles home with a sizeable leak in the coolant is a death knell to your motor. | |||||
| Windshield washer fluid in coolant reservoir | 20Relevance | 5 months ago | SubieLover | Submit Your Question HERE | |
| I have a 2019 Subaru Outback 2.5i 108k miles I've been busy with work and was about 2,000 miles overdue for an oil change, so I went to Farm & Fleet to get one. Thursday afternoon, I did a longer drive than normal, about 55 miles. I needed to add some washer fluid, so when I finished driving, I opened the hood and found my coolant extremely full. The liquid in the coolant reservoir was blue, whereas before it was universal green, as a body shop put in universal green when I hit a deer about 8 months ago. My washer fluid was empty, so I believe they added washer fluid to the coolant reservoir. When I called, they said they only fill washer fluid. They said I could come in, and after checking the cameras, they did see that someone filled it with washer fluid. As it is still separated from coolant and washer fluid, they are taking out the reservoir, emptying it all out, rinsing it, and then filling it with the correct coolant. They also drained the radiator and put in Peak Asian blue coolant. Do I need to worry about it mixing with the universal green? | |||||
| Answer to: 2018 since last coolant flush and change.. time for another one? | 20Relevance | 2 years ago | Hixster | Submit Your Question HERE | |
| Sure, a shop can change the coolant for you. You also can save money and change the coolant yourself. (Just make sure you have somewhere to dispose of that old fluid first) I would use the same type/color fluid that is in the car now. Toyota's recommendations for coolant changes are as follows: Red coolant - needs to be changed every 30,000 miles or every 2 years. Pink coolant - can last up to 100,000 miles or 10 years for the factory fill, then it needs to be changed every 60,000 miles or 5 years after that. You might consider having the brakes bled adding fresh fluid, it's been in ther 20 years if it's never been changed. | |||||
| 2013 crv coolant brand for coolant change | 16Relevance | 6 years ago | Lucusraider | Submit Your Question HERE | |
| I have a 2013 honda crv with only 30k miles. I use it on occasion around town and driving to upstate ny. I had the coolant changed at honda in 2015 and figure it's time to do it again but want to myself. I have 6 bottles of peak 50/50 coolant in my garage unopened sitting for 8 years. Can I use that or must I use honda coolant? People tell me I can only use honda brand because of aluminium radiator. Is that true or can i use my unopened peak bottles? | |||||
| coolant leaking from rear of the engine & coolant changing color | 16Relevance | 6 years ago | svi | Submit Your Question HERE | |
| Hi Scotty, i have Seat Leon 2003 1.8L automatic, 172000km. started noticing coolant leak from rear of the engine, probably underneath exhaust manifold and coolant started to get yellow-grayish. i see coolant loss after several drives. done headgadket block test with blue fluid and fluid did not change color. also every morning there is water coming out of the exhaust. it is not white smoke however. what might be the problem ? thanks. | |||||
| RE: 2010 Mazda 3 Coolant change only half of coolant changed | 16Relevance | 6 years ago | Figmund Sreud | Submit Your Question HERE | |
| Postscript: … I just checked to be sure: MAZDA EXTENDED LIFE coolant (FL22) "Premium Pre-diluted Antifreeze and Engine coolant (DO NOT ADD WATER)" … hence your coolant concentration is pretty, pretty low, … I suspect! F.S. | |||||
| Answer to: Pre-mixed coolant vs coolant that needs to be mixed with water? | 16Relevance | 6 years ago | InThrustWeTrust | Submit Your Question HERE | |
| It’s never a good idea to mix different coolant types. I would drain out the present coolant, flush the radiator and then add in the premix coolant (provided its compatible with your engine). Off topic, save me a string hopper tonight. | |||||
| Universal coolant in a Toyota | 15Relevance | 1 year ago | mpac7 | Submit Your Question HERE | |
| 2012 Sienna, v6, 202k miles. recently took it into a local shop to have some maintenance including a coolant flush. This car has had pink coolant its entire life. I failed to specify this to the shop and they flushed with a universal coolant. What are thoughts on the situation? Reading conflicting information online, whether universal coolant it’s OK to use in Toyotas. Thanks! | |||||
| Coolant sprayed in engine | 20Relevance | 2 years ago | RayneMan | Submit Your Question HERE | |
| I have a 2004 Dodge Intrepid SE. The vehicle has had a prolonged leak for roughly the last 4 years from the Climate Control Thermostat and the contecting hoses. Hoses were replaced but not the thermostat itself. Mechanic thought it was the water pump Gameplan was to drive it until the wheels fell off. Had to top off the coolant every other week. The car is typically a very smooth drive and yesterday the while coming to a stop the engine sputtered heavily and smoke poured out of the hood. When I opened the hood coolant had sprayed all over the engine near the coolant resevoir. I checked everywhere but could not find where the coolant sprayed from. All the hoses appeared to be intact. I did top of the coolant before I drove, the cap was tight. All of the coolant seemingly leaked out. Planning on taking it into a mechanic this week. Just looking for insight and thoughts. | |||||
| Answer to: Help with coolant system issue on 2008 Mazda 6 GH1 | 20Relevance | 2 years ago | isljam | Submit Your Question HERE | |
| @scottykilmer Thank you Scotty for taking time to reply. I was just watching your live stream at 1:30AM in Aus. The problem is I have purchased coolant already and my local mechanics won't accept customer sourced parts due to inability to guaruntee them and for liability. Also the coolant was actually quite hard to source. I could only find 2 products here in Aus that fit the service manual specs and Mazda factory FL22. I.e. P-OAT coolant (phosphate activated with no silicate, borate, nitrate and amines). The mechanic was just going to use some generic coolant with Silicates. Could I achieve similar results by simply repeating flushes of distilled water and finally radiator flush cleaner. Driving around in between flushes to get the car up to working temp/ heat on full (not sure if i need fan on) and the thermostat open? I dont mind taking time to get it right. Its just the process I'm not overly familiar with. The coolant doeesnt look too bad actually. It seems fairly clean. The car is 2008. I have to assume it's never been changed lookng at the service history, but the car only has 67000 miles on it. I can still flush and reverse flush the radiator. I am going to try my best to get at the heater core hoses, but not optomistic. Is there a way I can still flush the engine block with my integrated thermostat/housing.? Should i remove the whole thing? I've never attempted this before and it gets a little confusing where to insert the garden hose into what coolant hoses and which to unplug and connect. Can you please break ot down like you are speaking to a moron and offer any possible work around for me to do the flush myself besides paying a mechanic. Thank you Scotty. Love your work and your content. | |||||
| Losing coolant and bubbles in rad | 20Relevance | 4 years ago | CliffJr | Submit Your Question HERE | |
| Hi Scotty, About 2 years ago I bought 2008 Honda Civic EX - L4 - 1.8L 1799cc GAS MFI type R18A1, 2 dr cpe, 5-speed manual. It had 149K miles, no body damage, clean car fax. I bought it from a private seller that only asked $850 because it needed a new radiator and had some clear coat peeling from being a Texas car. I just wanted something that got better mileage to supplement my 92 GMC Sierra 1500 that while it ran well, it just turned over 375K miles and was getting about 10mpg when coasting downhill. It was lucky I bought the Honda when I did because the truck got totaled only a few short months later. I had a new radiator installed in the Honda and did a little tuning up. Changed all the fluids, installed new Denso ignition coils, rear bearings, all filters, PCV valve and NGK plugs and the car ran great. I noticed at about 175K miles that I was losing coolant, but finding no visible leaks and nothing on the driveway. It progressively got worse. I took it to my garage and they did a thorough compression test and found no head gasket leaks. They decided it was the radiator cap, which they replaced with a cheap aftermarket, but it quit drawing coolant from the overflow tank. I removed the overflow tank, cleaned and inspected for leaks or blockages, replaced all the tubing and replaced the radiator cap with a Denso. That did nothing to stop the coolant lose, but at least now it was drawing from the overflow tank. My mechanic recommended using some radiator stop leak, so I used Bar's Leaks Radiator Stop Leak Tablets, but the next day my thermostat was sticking closed. So I drained the radiator, flushed it with distilled water for over 30 minutes, drained again and replaced the thermostat with a Murray Ultra 170 Degree Thermostat, new gasket and refilled with fresh coolant. The coolant lose continued. I cleaned the motor and found a little seepage around the water pump area, so I had a new water pump, pump gasket and serpentine belt installed. I'm now at 189K miles and adding coolant every other day. When I attempt to burp it the bubbles never cease to flow. They are not very many bubbles, but even after 30 minutes I am getting consistent small bubbles. What would you recommend I look for next? Thanks in advance for your help! I love your show and find your honesty and advice exceedingly helpful. -Cliff in Kansas City, MO | |||||