Notifications
Clear all
Search result for: evans coolant
| # | Post Title | Result Info | Date | User | Forum |
| Kia Amanti 2006 leaking coolant | 20Relevance | 6 years ago | island505 | Submit Your Question HERE | |
| Hello Scotty, I have followed your YouTube posts for two years and have found them very helpful. I live in Puerto Rico. Here is my situation. I have a 2006 Kia Amanti with the 3.5L V6 engine, with 84,500 miles. To make the story short, the car overheated (due to crook mechanics at Kia Dealers), and now it's difficult to prove because the problems were caused about a year and a half ago, and the problem happened about three months. We let the engine cool, and reconnected the coolant hose that disconnected from the radiator, and refilled the radiator. At that time it seemed that everything was ok, no engine noises, but the car keeps slowly loosing coolant. Like for three days there is no sign of leaks, but hey, one morning I noticed the coolant in the garage floor. I refill it again. We have decided to use the car for short trips only, within one mile. The car is also leaking a bit of oil, when we asked another mechanic for diagnostic, I was told that it was not the crankcase seal, but another seal, located in an area “high” in the motor, that was very expensive to replace. I opted to use the AT-205 Re-seal and that helps. Last week we took the car for an oil change, the mechanic told us that the car is leaking coolant to the engine compartment, and he stated that the oil cap had residue that indicated that there was a coolant leak. I am fed up and decided to get a new car, and give this one in trade-in. I have seen many Stop leak coolant products, but I'm afraid that the contain silica and can cause harm in the motor. I don't want to make a private sell and later have a problem with the buyer, so I'm going to take it to a dealer for trade in. What products do you recommend that I can use to at least reduce the leak, so that when I take it for trade in, at least looks ok and is not leaking that much. By law, dealers have to fix cars out of major problems and give a two to four months warranty on used cars. Please consider that I live in an island and have not access to all products, and what I have close by is a Pep Boys and an Advanced Auto Parts available and Amazon takes two to three weeks (and I have Prime Service) to ship to Puerto Rico, and I would like to give this car in trade in before year end. Thanks for your help, sorry if my English sound funny or things are not correctly expressed or verb tense is incorrect, it is my second language. Cordially, Roberto | |||||
| 2002 Yukon Oil in Coolant but not vice versa | 20Relevance | 6 years ago | TheJarv | Submit Your Question HERE | |
| Hey Scotty, I recently bought a 2002 Yukon Denali with 180,000 miles and automatic transmission with 6.0 L V8. I had it pre purchase inspected by a mechanic and he found a leaking main seal and a knock sensor. But 1 week later... I looked closer and I have a layer of milkshakey goo on the bottom of the coolant reservoir and a thin layer of it along the inside of the heater hoses. The coolant otherwise looks pretty normal. But no coolant in the motor oil (that I can see.) No rough idle, no white smoke, no high engine temps, no observed coolant loss, in 100 miles of driving. Oil level hasn't gone down. Runs great, runs quiet, heat works, AC works, zippy on the freeway. 1) What could cause this? Wouldn't a head gasket leak cause bidirectional mixing? 2) Is there a way to detect coolant in oil before it looks funky? 3) Would this be a Bar's Leak candidate? 4) What should I do? Other details: No rough idle, no white smoke, no high engine temps, no observed coolant loss, in 100 miles of driving. Oil level hasn't gone down. Runs great, runs quiet, zippy on the freeway. Only engine code is for low voltage to knock sensor. No maintenance records available. Love this new (to me) rig and want to get at least a few years out of it! | |||||
| Heating issue in Opel Corsa (whether to fix or sell) | 19Relevance | 11 months ago | jaz059 | Submit Your Question HERE | |
| Can you tell me what is wrong with my car and whether it’s worth fixing. It’s a Vauxhall (Opel) corsa D, 2009, 142,000 miles. I have owned it since 2018 where it had 60,000 miles on it. I am based in the UK England. So far I have done the following works to it over the years. - new A/c compressor - new clutch- new alternator -recently new coil pack and spark plugs due to misfiring - new rear silencer as it fell off due to rust - changed rocker cover gasket - new oil pressure switch-changed oxygen and crankshaft sensor Now the heater is only blowing out lukewarm air not hot like it used to. I took it to a mechanic who looked at it for free and he said the following (not sure if it’s accurate). - doesn’t think it’s head gasket as there’s no white smoke from the exhaust, engine is not cranking when I start the car (starts first time). - he felt the two pipes in the engine bay and one was hotter than the other ( so it could be a circulation issue) - he touched the coolant with his hands and said it looks like something is mixing with the coolant. Could be oil or could be something someone who owned the car before me has added into the coolant (sealant of some sort). - said it could be water pump as that circulates the coolant around the engine. Timing chain is making a ticking noise and rattling on cold start so advised if changing the water pump might as well change timing chain also. Quoted me £500 for timing chain and water pump with parts and labour or £250/300 for labour only if I buy the parts. - said could try bleeding the cooling system and adding new coolant ( advised to get concentrated antifreeze and not the ready mixed) as concentrated is stronger. - advised to start using 10w 40 engine oil and not 5w 30 as thicker oil is better for older engine and it will stop the timing chain rattling. I don’t know how accurate that is ? - but I have also noted a leak underneath my car by the drivers side allow~ which could be coolant I can send pictures. So I’m not sure where I should start first. Should I get the leaks fixed first and try flushing the cooling system . Before doing timing chain and water pump ? - he also advised me to add white vinegar or radiator flush to the coolant reservoir and leave cap off and rev engine to 2000 rpm for 2 mins. Did that this afternoon myself Overall is there any value in doing any repairs with this high mileage. Cars value is approx £1000-£1500. | |||||
| Radiator Fan not working automatically | 19Relevance | 2 years ago | Mannan960 | Submit Your Question HERE | |
| Hi, This is my car details: 2012 Kia Sorento CRDI 4 Cyl Diesel 2.2L Odometer: 697,000 KM (approximately 430,000 miles) Engine is original since brand new Gearbox 520,000 KM (or 323,000 miles) I’m having 2 separated but related issues with my cooling system on my car. Issue 1: When the air con is switched off, the front radiator fan is ‘always off’. So the engine starts to gradually overheat, especially during idling. However, when I switch on the Air con, then the radiator fan kicks in and starts to work perfectly fine. I find this to be very abnormal, and very likely is a electrical issue. Recently I replaced all my fuel injectors with used parts, because they were too noisy and worn out, which were contributing to overheating at the time. However, at the moment I am convinced that my fuel injectors are working OK. And that the cooling issue is to do with the fan itself, not working when it should. Issue 2: The temperature gauge on my dash is not showing the correct reading. When engine starts overheating, the temperature gauge doesn’t correctly reflect. Instead, it shows middle / which is normal. Or it shows cold when car has been switched off for long, and then slowly goes up to middle. When the engine and coolant start overheating, or sometimes due to total loss of coolant, the temperature gauge does not indicate overheating. It still stays in the middle indicating normal operation. (which is false). Which itself is dangerous as it means I’ll end up cooking the engine if I don’t know of coolant leak and overheating. That’s why I purchased a digital heads up display, that connects to my OBD2 port. I am able to see the correct coolant and engine temperature from a digital OBD2 Heads Up Display HUD, which I purchased from ebay. However, the front radiator fan not turning on, unless Air Con is switched on. And the temperature gauge on my dash not correctly reflecting on true coolant and engine temperature overheating. I am not sure if there is any coolant leak, because of too much water condensation on bottom of the car due to air con running all the time. Although recently when doing oil change, I saw a tiny green coolant leak or bubble like drop on bottom of my AC compressor. My car is a right-hand drive, Australia left road. | |||||
| Answer to: Why is my car overheating? | 19Relevance | 2 years ago | Justin Shepherd | Submit Your Question HERE | |
| The transmission oil cooler and the cooling system are separate circuits. That means there's air in your cooling system. The heater works when hot coolant is circulated through the heater core, and only coolant. Hot air does nothing. Make sure the car has sat for a few hours, preferably with the hood open to allow residual heat to escape more efficiently. It'll be even better if you can leave it overnight. Get a set of ramps or park your car so that it's facing uphill. Pour coolant into your radiator so it's filled up. Start the car, put the heater on max heat, and full power. The level in the radiator will "burp" and decline slightly as coolant starts getting into the heater core. When it doesn't burp anymore, top off the coolant and fill the overflow to the "hot" level. Reach into the vehicle, the heater should be hot if the heater core is working properly. Then, identify where your leak is. They make UV dye that's compatible with antifreeze, get it and funky sunglasses so you can possibly identify the leak. Another option is to use a coolant pressure tester gauge. Read in your owner's manual the proper pressure reading for coolant, and pump it up to that pressure. Wait 15 minutes. If it noticeably declines after 15 minutes, you have a leak somewhere. It will be either on the ground or inside the engine. The head gasket is leaking if there's no evidence of spillage on the outside of the car, and there's a noticeable pressure drop. | |||||
| Answer to: Inside heating problems | 19Relevance | 2 years ago | Justin Shepherd | Submit Your Question HERE | |
| Only a seriously blown head gasket will show those symptoms (chunks of gasket nissing). There isn't enough coolant in the cooling system. The heater core operates with hot coolant, not hot air. Your coolant needs to be filled up before you can analyze further. You mentioned a leaking head gasket. If there's not enough coolant in the engine, it will blow the head gasket. | |||||
| Inside heating problems | 19Relevance | 2 years ago | sad boi | Submit Your Question HERE | |
| I'm lost for real. For 24 hours I've been trying to understand what's going on with my car. Yesterday I was at mechanics, tomorrow I'm going to the new place to do a double check to confirm the diagnose. My car is Nissan Qashqai 2012 J10 1.6 dci (diesel) FWD. Bought 3months ago. Month ago I went to mechanics to change oil and all the filters. After then I started noticing strange water sloshing sounds when accelerate and not always (mechanics told me that it may be coolant) and that was the time period when it started getting colder then when I turned on heating it didn't heat. I went to mechanics and they told me that something wasn't connected properly after changing cabin air filter. The heat still was not warm enough for human and it is also heating when you accelerate. Yesterday I went to other mechanics. The first thing they did was CO2 leak testing in coolant reservoir. Tester liquid changed from blue to green. They also noticed the cold engine strange sound, told something about the pressure somewhere, the capacity of coolant change in reservoir before and after. I stopped hearing things since they told me that the problem could with the head gasket. Notice: coolant reservoir is kinda turned into dark colour and the coolant inside is brown (i think because of age). I started googling a lot and I was trying to search for as many symptoms of head gasket problem as possible. But the only one thing that says it is head gasket problem - the CO2 test. Car drives good. Oil is clean (no milky color). Car is not overheating (the arrow is always pointed to the middle). I don't need to fill coolant. Didn't notice any bubbles in coolant reservoir. Car starts good (even when it is colder right now outside). Haven't seen some kind of white smoke coming out of exhaust. Overall what do we have? Tomorrow i'm going to another mechanics but I want to get as many opinions as possible. Some agrees that the car needs head gasket replacement, some say that there can be the problem with heater core etc etc. idk | |||||
| Head Gasket Leak | 19Relevance | 3 years ago | emmiemma | Submit Your Question HERE | |
| Hello Scotty I have Kia Cee'd ISG 2009 hatchback. The car has perfect service book. Now its been driven 150.000 KM. I live in Denmark in Europe. My car has been smoking a grey smoke. I just changed the oil on my car, and noticed on the cap a tiny bit of a "butter" there, which indicates that the head gasket is leaking (and probably really little since its a tiny bit of "butter" and coolant is leaking through the head gasket. (I didn't notice "butter" texture of the oil I removed from the engine, only this tiny bit on the cap. After watching your video here: How to Fix a Head Gasket Leak in Your Car Then I have those questions: 1. I replace the coolant with a new coolant, but how much of the steel seal has to be added into the coolant? (before starting the engine for 30 minutes, turn off the engine for 30 min and on again for 30 min. Repeat this 5 times you said.) 2. If I open the spark plugs to check if they have coolant on it, and lets say that 2-3 of the spark plugs have coolant, then I will simply remove all three of the spark plugs, and also disconnect the fuel injectors for that spark plugs. Will the engine still be able to run? 3. What is none of the spark plugs have visible coolant on them? How will I then fix the leakage of the head gasket? What will I do in this situation? Just leave all of the spark plugs inside as well as the fuel injectors. I hope that you can answer my questions 🙂 | |||||
| Answer to: White smoke out tailpipe | 19Relevance | 4 years ago | nta98 | Submit Your Question HERE | |
| Puffy white smoke is most likely burning coolant. There are multiple ways a headgasket can fail. If this is due to a failing headgasket, it would be the seal between a coolant jacket & a combustion chamber failing to seal, letting the car burn coolant. You could do 2 things to confirm this, check for the presence of exhaust gas in your coolant (theres a kit for that), and monitor your coolant level. It could also be something like a failing intake manifold gasket, allowing coolant to get into the intake runner, and burn. I would start there. Is it harder to start when cold, or does it have a misfire when cold? That could be from coolant getting into a cylinder as the engine cools down, and then making it harder for that cylinder to fire when you cold start it. | |||||
| 2009 Dodge Grand Cara SXT 3.8V6 scanned code P2181 | 19Relevance | 4 years ago | Aieda2021 | Submit Your Question HERE | |
| Hello I 'm very glad to be back. I have 5 codes P0571- Brake Switch 1 the ECM has detected that Brake Switch 1 is applied while Brake Switch 2 is open. P0573 Brake Switch 1 is off and the opposite of detected above. P0128 - Thermostat Rationality coolant temperature does not reach predicted engine coolant temperature within specified time. P2181 - coolant System Performance - The ECM has detected that the coolant temperature has......changed too slow or rapidly ( reoccurring problem after heater hoses were replaced 6 months ago) 4 probable causes A-Low coolant level (not) B-Engine Mechanical condition C- Open or Short Circuit condition D- Poor Electrical condition. P0116 - Engine coolant temperature sensor performance with 4 probable causes Three of the 4 listed above plus Power Train control module The red lightening bolt indicates the Throttle Control is an issue and Park the vehicle to reset and cool the engine but the engine doesn't get to overheating. There are absolutely no leaks from the coolant, water pump, radiator at all. One mechanic said it might be the " Sending Unit" ? I don't know. Every time I drive 3-4 miles the red lightening bolt indicator comes on. I'm in fort Wayne Indiana and I'm hoping someone in this community reside in fort Wayne so I could take my van to them. Most men here don't believe me because I'm totally female but I'm the one who has been maintenances my van for the past 4 years. By the way. I also watched Scotty's YouTube video about resetting your vehicle. I have yet to do. Out change places don't do that for my mileage Ugh! I need help to prevent myself from being taken advantage of. On mechanic refused to check out my concerns because I refused to leave my vehicle over night! 🙃 I'm not sure, but I'm confident that I could use some expert help from you guys. Aieda | |||||
| Answer to: Do I need a special tool for oil filter | 19Relevance | 5 years ago | darren_316 | Submit Your Question HERE | |
| Thank you Scotty, I actually got a great deal at Reilly Auto arts. I bought 4 Iridium spark plugs for $9 each but got a $15 gift card (other parts @ Reilly) and a $12 pre-paid card rebate. my net cost was only $2.25 per Autolite Iridium XP spark plug after rebates! yea me, lol. Oreilly told me that these iriduim plugs would work just fine. I installed them & works great, no issues. coolant/radiator - everything looks fine. so you said that I dont have to flush it. Three (3) questions on replacing the coolant. I saw on another tutorial video that mentioned draining the coolant. 1) drain thru the petcock; 2) drain the reservoir; and 3) drain the engine coolant in engine block by removing the bolt underside of the engine block - is this last step (#3) necessary? just want to do it right. I also saw that Toyotas use a red or pink coolant. should I get this specific type of coolant or would any other brand be suffice? Oreilly has 'Peak 1 concentrated' @$15 gal and walmart has 'Supertech extended life concentrated' @$10.46 gal. your thoughts on your coolant recommendation? ATF - Just drain and re-fill? no flush? I think one of your videos said to measure the amount of ATF drained & replace with the exact amount - is this correct? so I dont have to worry about replacing any tranny screen or filter? Oil Change - I was going to use Castrol Full Synthetic GTX 5W-30 & with STP extended life oil filter - on sale both for $30 Deeply appreciate your recommendations. Please advise. {black}:smile: | |||||
| 2017 Toyota Tacoma TRD Sport 4x4 Multiple Maintenance Questions | 19Relevance | 5 years ago | Stacie Girl | Submit Your Question HERE | |
| I would like suggestions from others who may have more knowledge about Toyotas than me and hopefully you all may have knowledge about my specific vehicle. My vehicle is a 2017 Toyota TRD Sport 4x4 with the 2GR-FKS Engine and the towing package too. I currently have 32,700 miles on it. I used my scan tool and it has no codes at all it is also an automatic transmission. Earlier today (Thursday April 21, 2022) I went down to a Toyota dealership to set an appointment to have my vehicle's engine oil changed, tires rotated and I also told the service advisor that I would like to get the coolant changed as well since the same coolant has been in my truck for 5 years now and when I tested it using some testing strips it showed that it needs to be changed soon because it is starting to become to acidic. I also mentioned to the service advisor that I would like the thermostat on my truck changed at the same time since there won't be any coolant in the engine when they drain the old coolant and before they put in the new coolant in. The service advisor told me that it would cost me additional $350 plus the cost of the thermostat just to change the thermostat at the same time the coolant flush would be done. Also the service advisor told me that my truck is too new to change the thermostat now and to wait for it to start to fail. But I am trying to think of things to change BEFORE they start to fail. I really think it is outrageous to charge an additional $350 just to change the thermostat at the same time while flushing the coolant. The service advisor said that it costs so much to change the thermostat for this engine because it is located in a place that is difficult to get to and that the technicians have to take half the engine apart to get to it. The service advisor also told me that I do NOT need to have my vehicle's engine oil changed or my tires rotated now because this person said that I have only driven 2,250 miles since it was last done. Which is true. I had my vehicle's engine oil changed at 30,450 miles on it. But the last time I had this done was 6 months ago. This is when the same dealership changed the engine oil and I asked them to use fully synthetic motor oil. They told me that they will use Mobil 1 Synthetic motor oil. So the service advisor basically told me to give them a call when I have driven at least another 2,500 miles or in six months. Then at that time to set up an appointment to get these things done. So I didn't get anything done to my truck today when I was driving back to my town here in Wyoming I was thinking of these questions. Is it better to wait to have my vehicle's engine oil changed by millage or by time? Do you all think I should have the thermostat changed now or to wait until it starts to fail or completely fails???? HOW LONG DO THE TOYTA THERMOSTATS LAST? The service advisor told me that they last a very long time. Which didn't help at all. Is it true that they have to take apart half the engine to get to the thermostat? I thought the thermostat was located close to the front of the engine by the big radiator fan. I live in Wyoming and as some of you may know this is the least populated state out of all 50 states (2020 Census State of Wyoming = 576,851) and it is the 10th largest state by land mass. So I don't want my truck to break down on me when I am in between cities and out in the middle of nowhere. Thank you for taking the time to read this and I look forward to hearing your suggestions. | |||||
| How to remove intake manifold on my 2000 Daewoo Nubira? | 19Relevance | 5 years ago | Daewoo Joe | Submit Your Question HERE | |
| ANY ADVICE ON REMOVING INTAKE MANIFOLD TO ACCESS CRACKED coolant PIPE UNDER INTAKE MANIFOLD 2000 Daewoo Nubira, AUTOMATIC TRANSMISSION, 2.0 4 CYL, FWD MILEAGE 160,000. I replaced the radiator and thermostat as radiator tank seam blew where a hairline crack was leaking so that was expected, as well as a pinhole leak in the resevoir tank which I replaced also. After the radiator and resevoir tank replaced the coolant plastic pipe under the intake manifold cracked where I may have had a very slow leak and crack, the engine was a junkyard replacement from approx 10 yrs ago so maybe the pipe was stressed in the engine replacement or just gave way due to age, heat. I have the aircleaner assembly off and a daewoo service manual and I think I can get the intake off to that I can replace that coolant pipe. Are there any tips for getting that intake off? I know I might have to disconnect where it connects to the muffler pipe or it may loosen where I can ease it back to get access to the coolant pipe located against the rear of the 4 cyl engine on the firewall side of the engine. any tips appreciated, I may end up getting all the part together, including any hoses I can get access to and let a mechanic do this but I think its worth trying since I recently put the radiator in. I replaced the same radiator maybe 6 or 7 yrs ago and no signs of head gasket problems which I suspected since my coolant system blew three times recently(1-the radiator tank where cracked, 2-the coolant resevoir-pinhle leak, 3-plastic coolant pipe under the intake) Thank you any tips appreciated. I could junk the car and buy a toyota but I am retired and have the time to work on it, like the car, and the taxes are very low on it | |||||
| Should I fix a blown head gasket or replace the engine? [2004 RAV4 4WD 207k mi, runs well, no OBD errors] | 19Relevance | 6 years ago | espongo | Submit Your Question HERE | |
| Hi everyone! New forum member, longtime Scotty Kilmer fan. I figured I'd ask for a second opinion here. Question: Should I fix a blown head gasket or replace the engine? I recently bought a 2004 Toyota RAV4 4WD from a private party with 207,000 miles, automatic transmission, no OBD errors, relatively new water pump, 2AZ-FE engine. A rookie mistake; I did not have a mechanic inspect the car before buying it. I intend to own the car for another 5+ years and use it to make 10-15 weekend trips to the mountains (400 mile roundtrip) a year, as well as 1-2 small trips in the city a week (say, 9000 miles/year). My mechanic has diagnosed a blown head gasket and says with a lower mileage vehicle, he'd typically just replace the gasket, but because it is a higher-mileage engine, recommends replacing the engine with a lower ~100k mileage one. It will cost more than double to replace the engine. Context: After purchasing the car, I drove it for about 20 miles and saw the engine temp was reaching red on the highway. I realized the coolant was low and added 1 gallon, then topped and burped the system. Over the next 2 weeks, I took it on a few 15 mile trips and then a 100 mile drive and at this time started smelling coolant blown into the cabin. After the 100 mile drive, I checked under the hood and started saw a good deal of dried coolant around the front of the engine near and below the exhaust manifold, dripping and evaporating down along the main exhaust pipe. About a quart of coolant was lost over 100 miles and the engine temp stayed normal during this time. The car drives powerfully and idles quietly. Before taking the car to the mechanic, I troubleshooted other parts of the coolant system: radiator, fans, radiator cap, hoses, and did an engine block test, which stayed blue. No white smoke from exhaust, no noticeable loss of power, no milky motor oil or froth, no oil in the coolant, no leaking from the back of the engine. So from what I can tell, the gasket issue is leaking coolant from the engine jacket to the outside front of the engine, not from the jacket to the combustion chambers/motor/cylinders/etc. There also doesn't seem to be a sign of stripped back of engine bolts that are common for this model of engine. | |||||
| RE: '06 Mazdaspeed 6 Power Loss, Sputtery feel in Acceleration | 19Relevance | 6 years ago | Razmig Bartassian | Submit Your Question HERE | |
| @joshhuck I understand that you may feel uncomfortable messing with the throttle body. I've done numerous throttle body cleanings before, and I've personally never had problems. Now in the case of your Mazda, it has coolant lines to disconnect. I've done a throttle body cleaning on my friend's Mazdaspeed, and I'd say a quart of coolant came out of the throttle body when we disconnected it (do this when the engine is cold...you can catch the coolant and reuse it). As for the bleeding process for your car, you need to remove the cap off the coolant reservoir and let the engine warm up to operating temperatures. Have your heater on the max setting. Once the thermostat opens up, the coolant will flow throughout the whole system and will release any trapped air out from the coolant reservoir. It's totally up to you if you feel comfortable enough to completely disconnect the throttle body. Worst case scenario, you could try cleaning it without disconnecting the coolant lines (but still disconnect the electrical connection), but you wouldn't be able to clean it as good. I don't want to force you to try something you don't feel comfortable doing. | |||||