Notifications
Clear all
Search result for: evans coolant
| # | Post Title | Result Info | Date | User | Forum |
| Check engine light and oil in coolant | 23Relevance | 4 years ago | RobertSz | Submit Your Question HERE | |
| Hi, My name is Robert. Living in UK but cars are very similar... 🤣 🤣 Brand: Vauxhall Model: Insignia 1.8L SRI Tourer Estate, Petrol, 2011 Milage:108.967 I was buy it couple of weeks before from a dealership ( first car, hope for long time). I took it to the garage to do basic thinks, and replace the rocker cover gasket and the 4 plugs ( engine oil and filter, air filter, transmission fluid, power steering fluid, coolant drain... brake pads and discs change , on head gasket test passed. Alsó asked him to put it on computer to find all issue.. I have 2 question as my mehanic saying it's fine, but I wants to fix before really some <profanity removed> happen. First question: Have some oil in the coolant after drain and change. I was read a lot.. it's can that the oil coolant faulty. I asked him to change it, he said it's working , the oil what I see in the coolant it's what stacked on the coolant tank wall, also he said monitor it before the,, surgery 😀 Do I have to push him to replace the oil coolant? Or any other idea why oil in the coolant. Second question is.. The check engine light illuminating all the time. Up on the top I was mention first car, I'm like a monkey for this thins.. My mechanic did not <profanity removed> said hello something wrong, I just realised when I was read the ovners manual. The manual book saying fault in catalytic converter. I went to him today , asked him to look on it, remove the converter and wash it as minimum £420+ labour a little bit much for a new one, if can wash it , wash it. He said with a smile that ,, I'm very sure it's not your catalic converter, it can be the sensor,, At this point I have to mention that no missfire, no engine idle issues, no noise... Drives well, but cannot compare with other cars...I don't know how it's do when suddenly accelerating and move with high speed as I'm in 🤮London. He was giving me ,,Forte Emission Reducer ,, to clean the converter, by the way he said will look in it.. Any other idea why the check engine light is on, exactly what tools I have to get to remove the converter by myself if he don't wants to wash it? Thank you, and sorry for my bad english... | |||||
| Coolant Question - 2001 f150 lariat 4-door | 23Relevance | 5 years ago | eddi3ownz | Submit Your Question HERE | |
| Hey guys, i just purchased a 01 f150. I was told the engine was swapped, so i have no idea what engine is in it, i think its the 4.6L but i dont realllly know. Anyways i want to do a coolant flush but i cant figure out what coolant to use, I have no idea what coolant is in the engine right now, i attached a picture of it. The manual says "Add Motorcraft Premium Engine coolant (green-colored),VC-4–A (U.S.) or CXC-10 (Canada) or Motorcraft PremiumGold Engine coolant (yellow-colored), VC-7–A, depending onthe type of coolant originally equipped in your vehicle. " But again, that would be for the factory engine. I'm a bit lost right now. Any help appreciated. ^ Theres a link to a video showing the current coolant. | |||||
| Answer to: Coolant smell 2002 Lexus IS300 | 17Relevance | 5 years ago | jack62 | Submit Your Question HERE | |
| So the coolant is either leaking onto a hot surface or leaking into a combustion chamber(s). You could buy a bottle of coolant Leak Dye and add into the radiator. Then you could use a UV light to see if any leaks are evident. (The location will glow green even if the coolant has evaporated) If you don't find any leaks, maybe watch Scotty's video on testing your coolant system for combustion gasses to rule out any coolant leaks into the combustion chambers. | |||||
| Milk white coolant | 17Relevance | 5 years ago | Chaseboy4 | Submit Your Question HERE | |
| What's good everyone? 2001 Honda Civic LX 5-Speed a lil over 166K miles. I open my radiator cap every morning to ensure I can see coolant however it was this morning I noticed the coolant was milk white. I took a cotton swab and swished it around and looked like milk. My thought is it has to do with the Head Gasket I could be wrong. There are no leaks anywhere nor is there any overheating or performance issues but I'm currently wondering why my coolant is white.... I did drain the radiator then refilled with fresh coolant but then here came the white coolant mixing with the fresh. What does everyone think about the color should I be concerned oooorrrrr...... | |||||
| Can I change my own coolant in my 2021 Sorento? | 17Relevance | 6 years ago | MrBob | Submit Your Question HERE | |
| Hi Scotti I bought a 2021 Sorento last December. I payed for and downloaded the Kia shop manual all 3800 pages from the KMA web sight. As I read I came across changing the coolant. It seems when you change the coolant you need a $6,000 KDS diagnostic and service tablet. This is because there is no coolant thermostat. There is a coolant control module which must be reset and bled after the coolant is replaced. I assume all new Hyundai's and Kia's are this way. Is there any way to do this manually or am I at the mercy of the dealer. Are other car brands doing stuff like this? If so just don't tell my wife. {black}:smile: | |||||
| Answer to: Topping off coolant 2016 RAV4 | 23Relevance | 6 years ago | jack62 | Submit Your Question HERE | |
| coolant colors. What do they mean? The pink coolant is an OAT (organic acid technology) that typically has a longer service life. The red coolant is just an "Extended Life" OAT (organic acid technology) HOAT You're fine mixing OAT with HOAT. You should NEVER mix OAT based formulas (which includes hoat) with IAT formulas. TYPE INHIBITOR TECHNOLOGY ZEREX coolant VEHICLES COLOR IAT (Inorganic Additive Technology) Silicates Zerex™ Original Older Vehicles GREEN OAT (Organic Acid Technology) Organic Acids Zerex™ Dex-Cool® GM, Saab, VW ORANGE HOAT (Hybrid OAT) Silicates & Organic Acids Zerex™ G-05™ Ford, Chrysler, European YELLOW HOAT (Hybrid OAT, Phosphate-free) NAP Free ZEREX™ G-48 BMW, Volvo, Tesla, Mini, others TURQUOISE P-HOAT (Phosphated HOAT) Phosphates & Organic Acids ZEREX™ Asian Vehicle Toyota, Nissan, Honda, Hyundai, KIA & other Asian vehicles PINK / BLUE Si-OAT (Silicated HOAT) Silicates & Organic Acids ZEREX™ G-40 Mercedes-Benz, Audi, VW, Porsche, others PURPLE | |||||
| Answer to: 2014 Ford Escape Disappearing Coolant | 23Relevance | 6 years ago | WildBill | Submit Your Question HERE | |
| Here are my suggestions in order: 1) Rent from an auto parts store a coolant system pressure tester 2) Google and find where the water pump and thermostat is on your car/engine. The Escape is popular so someone likely has made a YouTube video. 3) Run the pressure test and see if any coolant is weeping/leaking from the water pump or thermostat areas *when engine is cold*. If it does, those would be the first to replace to try to resolve. A slow leak from either of these places tend to hit the hot engine or other parts of the car and evaporate (remember coolant is normally 50% water). 4) The misfire likely isn't connected, but to be sure you can pull the spark plug back out and check the tip for any fouling from coolant or other fluids. Again, a quick Google search will provide image charts to compare different types of spark plug fouling to yours to get an idea if anything is wrong there. 5) If the pressure test comes back positive, really double check the overflow reservoir (most are plastic now and are known to crack with heat/age and a hairline crack will allow a very hard to detect slow leak) and or around on in the fins of the radiator. Where coolant leaks, it normally leaves a crusty looking crystal residue. 6) If you still can't find something, your best bet may be to go back to the mechanic, but consider finding one with a good reputation and knowledge of your make/model in your area. Facebook and NextDoor groups for your neighborhood are excellent sources to ask for references in this situation. I would really avoid using a coolant system leak additive like the Bar's Leak as those tend to gum up other parts of the coolant system too. This can cause additional repairs costs sooner down the road and or a sudden overheat leaving you stranded. | |||||
| Answer to: r33 taking so long to warm up and is less smooth when cold | 22Relevance | 5 years ago | Jonaeski | Submit Your Question HERE | |
| If your car is low on coolant, that heat never makes it to the fans in your ventilation system that blow the heat your way. Check your coolant levels if your car isn't warming up very fast because if that's the only issue, it's an easy fix. The engine has to warm up, and heat up the liquid coolant circulating throughout the engine, before any heat is available for people comfort. During winter, when outside temperatures are lower, that process takes longer. An efficient heater relies on the engine's cooling system components to all be functioning well. A thermostat stuck in the open position constantly pushes coolant into the engine and causes a lower operating temperature. Your temperature gauge will show a needle that barely increases or remains at the lowest setting. Your Heater Core or Engine Thermostat is Malfunctioning If the heater core is broken, or if the thermostat that measures how much heat is in the engine compartment, you are probably in for costly repairs. Your Water Pump is Malfunctioning Your coolant is moved around thanks to a component called a “water pump.” It’s called a water pump because the most basic coolant is water, but the coolant in your car should be mixed with antifreeze. If this pump isn’t working, your coolant will not move, and your heating system won’t feel like it’s working. | |||||
| Help, P0339, fixed? Now P0344 - 2006 Acura RL | 22Relevance | 2 years ago | SeatonBM | Submit Your Question HERE | |
| Sorry for the long read here, but I really could use a skilled pair of eyes to help me figure out a super intermittent problem - where details matter (hence the novel below)... My kid owns a 2006 Acura RL SH AWD, we replaced the timing belt using an ASIN kit from RockAuto, replaced the hydraulic tensioner, water pump, etc... After doing the timing belt, we verified that the timing was correct, rotating the crankshaft multiple times and ensuring that every time we were in Top Dead Center, everything aligned appropriately - and it did... We put it all back together, added new coolant, and test drove... The car ran smooth for days... A week or so after doing that job, we also had an auto shop replace the valve cover gaskets. Few days later we started getting a P0339 code, Crankshaft Position Sensor A intermittent fault, the car sat for a few weeks while we made time to essentially redo the timing belt job because the coolant level was also dropping a little, and the thought was that we didn't get as good of a seal when we replaced the water pump with the new gasket, and that maybe coolant was leaking into the Crankshaft Position Sensor below - causing the fault... So I ordered a replacement Crankshaft Position Sensor and a replacement water pump gasket... When we finally were ready to get the job done, the battery had died after sitting so long... So we pulled it out and replaced it... However now, because in hindsight, we pulled the battery, the fault code went away... And the car ran smooth again, coolant level also seemed to have stabilized - in hindsight I think the coolant level dropped because air was still being displaced from the system - we topped it off, and no longer had the coolant level fall anymore... So we shrugged it off and didn't do anything, and the car ran fine for a few days - until again, P0339... So we began to tear down the car again, disconnected the battery first, but when I took the lower timing cover off, I noticed it was dry under there, and with the coolant level no longer falling, I no longer felt we had a coolant leak after all, the Crankshaft Position Sensor was dry, so I just replaced the sensor, and didn't mess with the timing belt or water pump... Put it back together, and again, because the battery was disconnected, the fault cleared... And after it was all back together, we test drove, ran fine... For a few days... Few days later, the P0339 code returned, WTF... And after having replaced the sensor, I started checking connections, and found a loose ground bolt, where I believe the Crankshaft Position Sensor, Camshaft Position Sensor, and Knock Sensors all get grounded at - leaving a mystery as to why we were only getting a P0339 code and no codes related to the other sensors sharing that ground point... I tighten the ground bolt, reset the code by disconnecting the battery for a few minutes, reconnected the battery, and the car ran great, I now believe the original Crankshaft Position Sensor was not actually faulty, we had a bad ground........ Thing ran great after that........For a few weeks... Yesterday, we got our first code that wasn't P0339, now we got a P0344 code now, Cramshaft Position Sensor A intermittent fault - which again, shares that same ground point, but that ground is tightened now... Qe had the VSA and SHAWD lights come on too this time... The VSA and SHAWD light went away after restarting the car... For now, I also cleared the P0344 code by disconnecting/reconnecting the battery, but I know it'll be back, probably... I'm mentally preparing myself to tear down the car again to verify the timing, I'm starting to wonder if the timing belt jumped a tooth somewhere, although what has me puzzled now though, is why does the car run smoothly when the computer is reset, and no fault codes exist - if the belt jumped a tooth, resetting the computer doesn't fix that, shouldn't it then always run rough??? Other thoughts, what if it's a bad PCM? Or damaged connection though the only shared connection between the Crankshaft Position Sensor A and Camshaft Position Sensor A is that ground point - that is tight... Bad timing (belt jumped a tooth) is the next logical thought short of maybe somehow we coincidentally got a bad Camshaft Position Sensor... Other than that, we never did anything to let the computer "relearn" after replacing the Crankshaft Position Sensor, though... It ran fine without code for weeks despite that, and the initial fault was with the original Crankshaft Position Sensor... For now, since disconnecting/reconnecting the battery, all faults are gone, and the car runs great again... For now, but I know that will only last so long... Any thoughts??? | |||||
| Answer to: 2011 cruze coolant leak? | 17Relevance | 6 years ago | jimz | Submit Your Question HERE | |
| Does cooling system have overflow hose? The random loss of coolant could be from random use of the car. Sometimes driven hard. Sometimes not. The loss of coolant could be hidden at the end of a overflow hose that is hidden down closer to the bottom of radiator. Also, no coolant on ground because of evaporation on hot motor. If car is loosing coolant there should be evidence of it somewhere. If loss is not from operational reasons then look for hose leaks at water pump or heater hoses. Sometimes hose clamps fail and the coolant evaporates on the hot motor. Might also feel for water around heater core.. | |||||
| RE: 2015 Suburban oil and coolant | 17Relevance | 6 years ago | BC St | Submit Your Question HERE | |
| Is you oil lever over full? Is the oil milky? Have you checked the transmission fluid for coolant contamination? Do you think the coolant is getting into the engine oil or cylinders? You could try pulling the spark plugs and pressurize the system, although if it's loosing pressure as fast as you claim, and monitor it closely to keep the pressure up, then either crank the engine over and see if coolant sprays out of a spark plug hole, or use a bore scope to look for coolant in a cylinder. If you haven't done so already, you might want to perform a combustion leak test with the blue chemical. You never know. Put some dye in the coolant and see if it shows up on the A/C drain. | |||||
| Jetta coolant light keeps popping up | 17Relevance | 6 years ago | Marco 3515 | Submit Your Question HERE | |
| I recently flushed out my old coolant in my 04 jetta but when i try to put in the new coolant it just stays at the top of the reservoir until i drive for a little then the coolant light pops up and the level goes down ive been putting in water and coolant for about 4 days now there is no leak and i am wondering if the coolant is ever going to get filled so this stupid light doesn’t keep popping up | |||||
| Answer to: 2010 Dodge Charger hemi problems | 16Relevance | 6 years ago | Razmig Bartassian | Submit Your Question HERE | |
| When was the last time your coolant was changed? Although it has 145,000 miles, it's a 2010. coolant should be changed at a maximum every 4 years to ensure nothing gets corroded. coolant gets old over time and will turn into that chocolate milk color. Most likely there is no oil dilution at all...just some really old coolant that needs to be flushed out properly. I would also suggest changing the radiator out as well because of how bad the coolant got. Now if the coolant was changed recently like a year or two before, then I would be concerned with a cracked head. | |||||
| Answer to: Head Gasket Leak | 22Relevance | 3 years ago | Justin Shepherd | Submit Your Question HERE | |
| No, assuming it's a V6, it won't have enough "oomph" to get past the dead cylinders if you do that. You can probably afford to lose 1 cylinder and the engine will run unevenly, maybe two if the timing is right. If it's a 4-cylinder, forget about it. The engine won't stay running with any dead cylinder. I have a 1979 Pontiac that started misfiring when it was cold and as it heated up, the misfiring seemed to go away. Spark plugs had loosened up on two of the engine's 8 cylinders. Simply unbolting the spark plugs and examining them should be good enough. Look for evidence of the plugs being steam cleaned. If there's coolant on the spark plugs, you really blew that head gasket. You can also buy a head gasket tester off of Amazon. I don't know the policies of auto parts stores overseas and whether or not they have tools available to rent. Confirm it's actually a head gasket leak, first. Products like Steel Seal may work, depending on where the head gasket is leaking. It uses sodium silicate, which hardens immediately when the spark plug fires if it's leaking into a combustion chamber. I would rather fix the issue the right way as opposed to using some kind of "miracle in a bottle". You could very easily make things worse, and coolant is the lifeblood of the engine. That thing is old enough, are you sure you didn't knock a hose off when you were changing the oil? The PCV valve controls whether or not blow-by from the pistons gets back into the intake manifold to be reburned. Knocking the hose off that leads to the PCV valve will cause condensation on the highest part of the engine's oil system- the oil cap, especially when it's cold outside. When a shop was replacing my valve cover gaskets last year, they neglected to put the PCV valve back, and when it turned cold, I checked the oil and there was a frozen "milkshake" on it. Apparently, the shop forgot to reinsert the PCV valve. I don't go to that shop anymore. | |||||
| Overheating issues | 22Relevance | 5 years ago | MBell0185 | Submit Your Question HERE | |
| 2015 Dodge Charger Se 3.6l RWD automatic 65.790 miles my car is overheating this is issue did happen into I got a oil change with coolant top off the so called mechanic took the overflow cap off the car while it was under pressure to top off the coolant in doing so he slammed the cap back on the tank after coolant sprayed everywhere and than he took it back off and fill it up with a universal coolant and my car use a organic coolant I had the coolant system flushed I change the water pump, temperature sensors, thermostat a few times, overflow tank and caps I have no check engine light, no smoke coming from under the hood or tail pipe but I have noticed that after driving for almost an hour it starts to oveheat and the coolant is backed up in the overflow tank and coolant is leaking out of the overflow hoes there is a lot of pressure on the upper radiator hose and my fan is running extremely high the temperature gage is high and the car doesn't shut off when overheating I was told that my head gasket could have warped and the crazy part is it pass pressure test and everything check out good on the diagnostic do you have any idea what this could be ? | |||||